View ISP1506A08_4266451.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

IMPORTANT NOTICE
Dear customer, As from August 2nd 2008, the wireless operations of NXP have moved to a new company, ST-NXP Wireless. As a result, the following changes are applicable to the attached document.
Company name - NXP B.V. is replaced with ST-NXP Wireless. Copyright - the copyright notice at the bottom of each page "(c) NXP B.V. 200x. All rights reserved", shall now read: "(c) ST-NXP Wireless 200x - All rights reserved". Web site - http://www.nxp.com is replaced with http://www.stnwireless.com Contact information - the list of sales offices previously obtained by sending an email to salesaddresses@nxp.com , is now found at http://www.stnwireless.com under Contacts.
If you have any questions related to the document, please contact our nearest sales office. Thank you for your cooperation and understanding. ST-NXP Wireless
www.stnwireless.com
ISP1506A; ISP1506B
ULPI Hi-Speed USB OTG transceiver
Rev. 02 -- 28 August 2008 Product data sheet
1. General description
The ISP1506 is a Universal Serial Bus (USB) On-The-Go (OTG) transceiver that is fully compliant with Ref. 1 "Universal Serial Bus Specification Rev. 2.0", Ref. 2 "On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3" and Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1". The ISP1506 can transmit and receive USB data at high-speed (480 Mbit/s), full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s), and provides a pin-optimized, physical layer front-end attachment to USB host, peripheral and OTG devices. It is ideal for use in portable electronic devices, such as mobile phones, digital still cameras, digital video cameras, Personal Digital Assistants (PDAs) and digital audio players. It allows USB Application-Specific Integrated Circuits (ASICs), Programmable Logic Devices (PLDs) and any system chip set to interface with the physical layer of the USB through an 8-pin interface. The ISP1506 can interface to devices with digital I/O voltages in the range of 1.65 V to 1.95 V. The ISP1506 is available in HVQFN24 package.
2. Features
I Fully complies with: N Ref. 1 "Universal Serial Bus Specification Rev. 2.0" N Ref. 2 "On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3" N Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1" I Interfaces to host, peripheral and OTG device cores; optimized for portable devices or system ASICs with built-in USB OTG device core I Complete Hi-Speed USB physical front-end solution that supports high-speed (480 Mbit/s), full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s) N Integrated 45 10 % high-speed termination resistors, 1.5 k 5 % full-speed device pull-up resistor, and 15 k 5 % host termination resistors N Integrated parallel-to-serial and serial-to-parallel converters to transmit and receive N USB clock and data recovery to receive USB data up to 500 ppm N Insertion of stuff bits during transmit and discarding of stuff bits during receive N Non-Return-to-Zero Inverted (NRZI) encoding and decoding N Supports bus reset, suspend, resume and high-speed detection handshake (chirp) I Complete USB OTG physical front-end that supports Host Negotiation Protocol (HNP) and Session Request Protocol (SRP)
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
I
I
I I I
N Integrated 5 V charge pump; also supports external charge pump or 5 V VBUS switch N Complete control over bus resistors N Data line and VBUS pulsing session request methods N Integrated VBUS voltage comparators N Integrated cable (ID) detector Highly optimized ULPI compliant N 60 MHz, 8-bit interface between the core and the transceiver N Supports 4-bit dual-edge data bus N Supports 60 MHz output clock configuration N Integrated Phase-Locked Loop (PLL), supporting one crystal or clock frequency: 19.2 MHz (ISP1506ABS) and 26 MHz (ISP1506BBS) N Fully programmable ULPI-compliant register set N Internal Power-On Reset (POR) circuit Flexible system integration and very low current consumption, optimized for portable devices N Power-supply input range is 3.0 V to 3.6 V N Internal voltage regulator supplies 3.3 V and 1.8 V N Charge pump regulator outputs 4.75 V to 5.25 V at a current of up to 50 mA, tunable using an external capacitor N Supports interfacing I/O voltage of 1.65 V to 1.95 V; separate I/O voltage pins minimize crosstalk N Typical operating current of 10 mA to 48 mA, depending on the USB speed and bus utilization; not including the charge pump N Typical suspend current of 35 A Full industrial grade operating temperature range from -40 C to +85 C 4 kV ElectroStatic Discharge (ESD) protection at pins DP, DM, ID, VBUS and GND Available in a small HVQFN24 (4 mm x 4 mm) Restriction of Hazardous Substances (RoHS) compliant, halogen-free and lead-free package
3. Applications
I I I I Digital still camera Digital TV Digital Video Disc (DVD) recorder External storage device, for example: N Magneto-Optical (MO) drive N Optical drive: CD-ROM, CD-RW, DVD N Zip drive Mobile phone MP3 player PDA Portable Media Player (PMP) Printer Scanner
(c) NXP B.V. 2008. All rights reserved.
I I I I I I
ISP1506A_ISP1506B_2
Product data sheet
Rev. 02 -- 28 August 2008
2 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
I Set-Top Box (STB) I Video camera
4. Ordering information
Table 1. Part Type number Marking Crystal or clock frequency 19.2 MHz 26 MHz Ordering information Package Name Description Version
ISP1506ABS ISP1506BBS
06A[1] 06B[1]
HVQFN24 HVQFN24
plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 4 x 4 x 0.85 mm plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 4 x 4 x 0.85 mm
SOT616-1 SOT616-1
[1]
The package marking is the first line of text on the IC package and can be used for IC identification.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
3 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
5. Block diagram
CLOCK STP ULPI INTERFACE DIR NXT
4
19 17 16 18 20, 22, 23, 24 ULPI INTERFACE CONTROLLER TERMINATION RESISTORS USB DATA SERIALIZER 4 HS USB ATX DP
USB DATA DESERIALIZER VBUS valid external
3
DM
DATA[3:0] REGISTER MAP
USB CABLE OTG MODULE ID DETECTOR 5 ID
DRV VBUS DRV VBUS external
RESET_N/ PSW_N
14 POWER-ON RESET global reset
VBUS COMPARATORS 10 SRP CHARGE AND DISCHARGE RESISTORS VBUS/ FAULT
PLL global clocks XTAL1 XTAL2 VCC(I/O) REG3V3 REG1V8 VCC 12 13 1, 21 CRYSTAL OSCILLATOR
5 V CHARGE PUMP SUPPLY
8 7 6
C_A C_B CPGND
interface voltage internal power
ISP1506
11 15 9 VOLTAGE REGULATOR VREF BAND GAP REFERENCE VOLTAGE 2 RREF
004aaa598
Fig 1.
Block diagram
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
4 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
6. Pinning information
6.1 Pinning
21 VCC(I/O) 19 CLOCK 18 NXT 17 STP 16 DIR 15 REG1V8 14 RESET_N/PSW_N 13 XTAL2 VBUS/FAULT 10 REG3V3 11 XTAL1 12 7 8 9
004aaa599
terminal 1 index area VCC(I/O) RREF DM DP ID CPGND 1 2 3 4 5 6
ISP1506
C_B
Transparent top view
Fig 2.
Pin configuration HVQFN24; top view
6.2 Pin description
Table 2. VCC(I/O) RREF DM DP ID Pin description Pin 1 2 3 4 5 Type[4] P AI/O AI/O AI/O I Description I/O supply rail resistor reference data minus (D-) pin of the USB cable data plus (D+) pin of the USB cable identification (ID) pin of the micro-USB cable If this pin is not used, it is recommended to connect it to REG3V3. plain input; TTL level CPGND C_B C_A VCC VBUS/FAULT 6 7 8 9 10 P AI/O AI/O P AI/O charge pump ground flying capacitor pin connection for the charge pump flying capacitor pin connection for the charge pump input supply voltage or battery source This pin has two possible functions: VBUS (analog input and output) -- VBUS pin of the USB cable FAULT (input) -- Input pin for the external VBUS digital overcurrent or fault detector signal If this pin is not used as either VBUS or FAULT, it must be connected to ground. plain input; 5 V tolerant REG3V3 XTAL1 XTAL2
ISP1506A_ISP1506B_2
Symbol[1][2][3]
11 12 13
P AI AO
3.3 V regulator output crystal oscillator or clock input crystal oscillator output
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
C_A
VCC
20 DATA3
24 DATA0
23 DATA1
22 DATA2
5 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 2. RESET_N/ PSW_N
Pin description ...continued Pin 14 Type[4] I/O Description This pin has two possible functions: RESET_N (input) -- Active LOW asynchronous reset input 3.3 V tolerant; plain input PSW_N (output) -- Active LOW external VBUS power switch or external charge pump enable open-drain; 3.3 V tolerant If not used, this pin must be connected to VCC(I/O).
Symbol[1][2][3]
REG1V8 DIR STP NXT CLOCK DATA3 VCC(I/O) DATA2 DATA1 DATA0 GND
15 16 17 18 19 20 21 22 23 24 die pad
P O I O O I/O P I/O I/O I/O P
1.8 V regulator output ULPI direction signal slew-rate controlled output (1 ns) ULPI stop signal plain input; programmable pull up ULPI next signal slew-rate controlled output (1 ns) 60 MHz clock output 2 mA output drive pin 3 of the bidirectional ULPI data bus 2 mA output drive; plain input; programmable pull down I/O supply rail pin 2 of the bidirectional ULPI data bus 2 mA output drive; plain input; programmable pull down pin 1 of the bidirectional ULPI data bus 2 mA output drive; plain input; programmable pull down pin 0 of the bidirectional ULPI data bus 2 mA output drive; plain input; programmable pull down ground supply; down bonded to the exposed die pad (heat sink); to be connected to the PCB ground
[1] [2] [3] [4]
A detailed description of these pins can be found in Section 7.9. Symbol names ending with an underscore N (for example, NAME_N) indicate active LOW signals. For details on external components required on each pin, see bill of materials and application diagrams in Section 16. I = input; O = output; I/O = digital input/output; AI = analog input; AO = analog output; AI/O = analog input/output; P = power or ground pin.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
6 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
7. Functional description
7.1 ULPI interface controller
The ISP1506 provides an 8-pin interface that is compliant with Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1". This interface must be connected to the USB link. The ULPI interface controller provides the following functions:
* * * * * * * * * * *
ULPI compliant and register set Allows full control over the USB peripheral, host and OTG functionality Parses the USB transmit and receive data Prioritizes the USB receive data, USB transmit data, interrupts and register operations Control of the VBUS charge pump or external source VBUS monitoring, charging and discharging Low-power mode 3-pin serial mode Generates RXCMDs (status updates) Maskable interrupts Control over the ULPI bus state; can attach weak pull-down resistors to DATA[3:0]
For more information on the ULPI protocol, see Section 9.
7.2 USB data serializer and deserializer
The USB data serializer prepares data to transmit on the USB bus. To transmit data, the USB link sends a transmit command and data on the ULPI bus. The serializer performs parallel-to-serial conversion, bit stuffing and NRZI encoding. For packets with a PID, the serializer adds a SYNC pattern to the start of the packet, and an EOP pattern to the end of the packet. When the serializer is busy and cannot accept any more data, the ULPI interface controller deasserts NXT. The USB data deserializer decodes data received from the USB bus. When data is received, the deserializer strips the SYNC and EOP patterns, and then performs serial-to-parallel conversion, NRZI decoding and discarding of stuff bits on the data payload. The ULPI interface controller sends data to the USB link by asserting DIR, and then asserting NXT whenever a byte is ready. The deserializer also detects various receive errors, including bit stuff errors, elasticity buffer underrun or overrun, and byte-alignment errors.
7.3 Hi-Speed USB (USB 2.0) ATX
The Hi-Speed USB ATX block is an analog front-end containing the circuitry needed to transmit, receive and terminate the USB bus in high-speed, full-speed and low-speed, for USB peripheral, host and OTG implementations. The following circuitry is included:
* Differential drivers to transmit data at high-speed, full-speed and low-speed * Differential and single-ended receivers to receive data at high-speed, full-speed and
low-speed
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
7 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
* * * * *
Squelch circuit to detect high-speed bus activity High-speed disconnect detector 45 high-speed bus terminations on DP and DM for peripheral and host modes 1.5 k pull-up resistor on DP for full-speed peripheral mode 15 k bus terminations on DP and DM for host and OTG modes
For details on controlling resistor settings, see Table 7.
7.4 Voltage regulator
The ISP1506 contains a built-in voltage regulator that conditions the VCC supply for use inside the ISP1506. The voltage regulator:
* Supports input supply range of 3.0 V < VCC < 3.6 V * Supplies internal circuitry with 1.8 V and 3.3 V
Remark: The REG1V8 and REG3V3 pins require external decoupling capacitors. For details, see Section 16.
7.5 Crystal oscillator and PLL
The ISP1506 has a built-in crystal oscillator and a Phase-Locked Loop (PLL) for clock generation. The crystal oscillator takes a sine-wave input from an external crystal, on the XTAL1 pin, and converts it to a square wave clock for internal use. Alternatively, a square wave clock of the same frequency can also be directly driven into the XTAL1 pin. Using an existing square wave clock can save the cost of the crystal and also reduce the board size. The PLL takes the square wave clock from the crystal oscillator, and multiplies or divides it into various frequencies for internal use. The PLL produces the following frequencies, irrespective of the clock source:
* * * * *
60 MHz clock for the ULPI interface controller 1.5 MHz for the low-speed USB data 12 MHz for the full-speed USB data 480 MHz for the high-speed USB data Other internal frequencies for data conversion and data recovery
7.6 OTG module
This module contains several sub-blocks that provide all the functionality required by the USB OTG specification. Specifically, it provides the following circuits:
* The ID detector to sense the ID pin of the micro-USB cable. The ID pin dictates which
device is initially configured as the host and which as the peripheral.
* VBUS comparators to determine the VBUS voltage level. This is required for the VBUS
detection, SRP and HNP.
* Resistors to temporarily charge and discharge VBUS. This is required for SRP.
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
8 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
* Charge pump to provide 5 V power on VBUS. The downstream peripheral can draw its
power from the ISP1506 VBUS.
7.6.1 ID detector
The ID detector detects which end of the micro-USB cable is plugged in. The detector must first be enabled by setting the ID_PULLUP register bit to logic 1. If the ISP1506 senses a value on ID that is different from the previously reported value, an RXCMD status update will be sent to the USB link, or an interrupt will be asserted.
* If the micro-B end of the cable is plugged in, the ISP1506 will report that ID_GND is
logic 1. The USB link must change to peripheral mode.
* If the micro-A end of the cable is plugged in, the ISP1506 will report that ID_GND is
logic 0. The USB link must change to host mode.
7.6.2 VBUS comparators
The ISP1506 provides three comparators, VBUS valid comparator, session valid comparator and session end comparator, to detect the VBUS voltage level. 7.6.2.1 VBUS valid comparator This comparator is used by hosts and A-devices to determine whether the voltage on VBUS is at a valid level for operation. The ISP1506 minimum threshold for the VBUS valid comparator is VA_VBUS_VLD. Any voltage on VBUS below VA_VBUS_VLD is considered invalid. During power-up, it is expected that the comparator output will be ignored. 7.6.2.2 Session valid comparator The session valid comparator is a TTL-level input that determines when VBUS is high enough for a session to start. Peripherals, A-devices and B-devices use this comparator to detect when a session is started. The A-device also uses this comparator to determine when a session is completed. The session valid threshold of the ISP1506 is VB_SESS_VLD, with a hysteresis of Vhys(B_SESS_VLD). 7.6.2.3 Session end comparator The ISP1506 session end comparator determines when VBUS is below the B-device session end threshold. The B-device uses this threshold to determine when a session has ended. The session end threshold of the ISP1506 is VB_SESS_END.
7.6.3 SRP charge and discharge resistors
The ISP1506 provides on-chip resistors for short-term charging and discharging of VBUS. These are used by the B-device to request a session, prompting the A-device to restore the VBUS power. First, the B-device makes sure that VBUS is fully discharged from the previous session by setting the DISCHRG_VBUS register bit to logic 1 and waiting for SESS_END to be logic 1. Then the B-device charges VBUS by setting the CHRG_VBUS register bit to logic 1. The A-device sees that VBUS is charged above the session valid threshold and starts a session by turning on the VBUS power.
7.6.4 Charge pump
The ISP1506 uses a built-in charge pump to supply current to VBUS at a nominal voltage of 5 V. The charge pump works as a capacitive DC-DC converter. An external holding capacitor, Ccp(C_A)-(C_B), is required between the C_A and C_B pins as shown in Figure 3,
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
9 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
which also shows a typical OTG VBUS load. The value of Ccp(C_A)-(C_B) depends on the amount of current drive required. If the internal charge pump is not used, the Ccp(C_A)-(C_B) capacitor is not required. For details on the C_A and C_B pins, see Section 7.9.7.
VBUS
0.1 F
OTG VBUS
4.7 F
ISP1506
C_B
Ccp(C_A)-(C_B)
C_A
004aaa600
Fig 3.
External capacitors connection
7.7 Band gap reference voltage
The band gap circuit provides a stable internal voltage reference to bias the analog circuitry. The band gap requires an accurate external reference resistor RRREF connected between the RREF and GND pins. For details, see Section 16.
7.8 Power-On Reset (POR)
The ISP1506 has an internal power-on-reset circuit that resets all internal logic on power-up. The ULPI interface is also reset on power-up. Remark: When CLOCK starts toggling after power-up, the USB link must issue a reset command over the ULPI bus to ensure correct operation of the ISP1506.
7.9 Detailed description of pins
7.9.1 DATA[3:0]
The ISP1506 is a Physical layer (PHY) containing a USB transceiver. DATA[7:0] is a dual-edge bidirectional data bus. The USB link must drive DATA[3:0] to LOW when the ULPI bus is idle. When the link has data to transmit to the PHY, it drives a nonzero value. The data bus can be reconfigured to carry various data types, as given in Section 8 and Section 9.
7.9.2 VCC(I/O)
The input power pin that sets the I/O voltage level. For details, see Section 12, Section 13 and Section 16. VCC(I/O) provides power to on-chip pads of the following pins:
* * * * *
ISP1506A_ISP1506B_2
CLOCK DATA[3:0] DIR NXT RESET_N/PSW_N
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
10 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
* STP
7.9.3 RREF
Resistor reference analog I/O pin. A resistor, RRREF, must be connected between RREF and GND, as shown in Section 16. This provides an accurate voltage reference that biases internal analog circuitry. Less accurate resistors cannot be used and will render the ISP1506 unusable.
7.9.4 DP and DM
DP (data plus) and DM (data minus) are USB differential data pins. These must be connected to the D+ and D- pins of the USB receptacle.
7.9.5 ID
For OTG implementations, the ID (identification) pin is connected to the ID pin of the micro-USB receptacle. As defined in Ref. 2 "On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3", the ID pin dictates the initial role of the link. If ID is detected as HIGH, the link must assume the role of a peripheral. If ID is detected as LOW, the link must assume a host role. Roles can be swapped at a later time by using HNP. If the ISP1506 is not used as an OTG PHY, but as a standard USB host or peripheral PHY, the ID pin must be connected to REG3V3.
7.9.6 CPGND
CPGND indicates the analog ground for the on-board charge pump. CPGND must always be connected to ground, even when the charge pump is not used.
7.9.7 C_A and C_B
The C_A and C_B pins are to connect the flying capacitor of the charge pump. The output current capability of the charge pump depends on the value of the capacitor used, as shown in Table 3. For maximum efficiency, place capacitors as close as possible to pins. For details, see Section 16. If the charge pump is not used, C_A and C_B must be left floating (not connected).
C_A
Ccp(C_A)-(C_B)
ISP1506
C_B
VBUS
IL
004aaa601
Fig 4.
Charge pump capacitor
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
11 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Recommended charge pump capacitor value IL (max) 8 mA 50 mA
Table 3. 22 nF 270 nF
Ccp(C_A)-(C_B)
7.9.8 VCC
VCC is the main input supply voltage for the ISP1506. Decoupling capacitors are recommended. For details, see Section 16.
7.9.9 VBUS/FAULT
This pin provides two options for VBUS driving and monitoring. If neither function is used, this pin must be connected to ground. 7.9.9.1 VBUS This pin acts as an input to VBUS comparators, and also as a power pin for the charge pump, and SRP charge and discharge resistors. The VBUS pin requires a capacitive load as shown in Section 16. To prevent electrical overstress, it is strongly recommended that you attach a series resistor on the VBUS pin (RVBUS). RVBUS must not be attached when using the ISP1506 internal charge pump. For details, see Section 16. 7.9.9.2 FAULT (external overcurrent or fault detector) If an external VBUS overcurrent or fault circuit is used, the output fault indicator of that circuit can be connected to the ISP1506 FAULT input pin. The ISP1506 will inform the link of VBUS fault events by sending RXCMDs on the ULPI bus. To use the FAULT pin, the link must:
* Set the USE_EXT_VBUS_IND register bit to logic 1. * Set the polarity of the external fault signal using the IND_COMPL register bit.
7.9.10 REG3V3 and REG1V8
Regulator output voltage. These supplies are used to power the ISP1506 internal digital and analog circuits, and must not be used to power external circuits. For correct operation of the regulator, it is recommended that you connect REG3V3 and REG1V8 to decoupling capacitors. For examples, see Section 16.
7.9.11 XTAL1 and XTAL2
XTAL1 is the crystal input, and XTAL2 is the crystal output. The allowed frequency on the XTAL1 pin depends on the ISP1506 product version. The ISP1506 requires external load capacitors to GND on each terminal of the crystal. For details, see Section 16. If at any time the system wants to stop the clock on XTAL1, the link must first put the ISP1506 into low-power mode. The clock on XTAL1 must be restarted before low-power mode is exited.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
12 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
7.9.12 RESET_N/PSW_N
This pin provides two optional functions. If neither function is used, this pin must be connected to VCC(I/O). 7.9.12.1 RESET_N An active LOW asynchronous reset pin that resets all circuits in the ISP1506. The ISP1506 contains an internal power-on reset circuit, and therefore using the RESET_N pin is optional. If RESET_N is not used, it must be connected to VCC(I/O). For details on using RESET_N, see Section 9.3.2. 7.9.12.2 PSW_N PSW_N is an active LOW, open-drain output pin. This pin can be connected to an active LOW, external VBUS switch or charge pump enable circuit to control the external VBUS power source. An external pull-up resistor, Rpullup, is required when PSW_N is used. This pin is open-drain, allowing ganged-mode power control for multiple USB ports. For application details, see Section 16. To use the PSW_N pin, the link must disable the reset input by setting the IGNORE_RESET bit in the Power Control register to logic 1. This will ensure that PSW_N is not misinterpreted as a reset. If the link is in host mode, it can enable the external VBUS power source by setting the DRV_VBUS_EXT bit in the OTG Control register to logic 1. The ISP1506 will drive PSW_N to LOW to enable the external VBUS power source. If the link detects an overcurrent condition (the VBUS state in RXCMD is not 11b), it must disable the external VBUS power source by setting DRV_VBUS_EXT to logic 0.
7.9.13 DIR
ULPI direction output pin. Controls the direction of the data bus. By default, the ISP1506 holds DIR at LOW, causing the data bus to be an input. When DIR is LOW, the ISP1506 listens for data from the link. The ISP1506 pulls DIR to HIGH only when it has data to send to the link, which is for one of two reasons:
* To send the USB receive data, RXCMD status updates and register reads data to the
link.
* To block the link from driving the data bus during power-up, reset and low-power
mode (suspend). For details on DIR usage, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1".
7.9.14 STP
ULPI stop input pin. The link must assert STP to signal the end of a USB transmit packet or a register write operation. When DIR is asserted, the link can optionally assert STP to abort the ISP1506, causing it to deassert DIR in the next clock cycle. A weak pull-up resistor is incorporated into the STP pin as part of the interface protect feature. For details, see Section 9.3.1. For details on STP usage, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1".
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
13 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
7.9.15 NXT
ULPI next data output pin. The ISP1506 holds NXT at LOW by default. When DIR is LOW and the link is sending data to the ISP1506, NXT will be asserted to notify the link to provide the next data byte. When DIR is at HIGH and the ISP1506 is sending data to the link, NXT will be asserted to notify the link that another valid byte is on the bus. NXT is not used for register read data or the RXCMD status update. For details on NXT usage, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1".
7.9.16 CLOCK
A 60 MHz output interface clock to synchronize the ULPI bus. The ISP1506 provides two clocking options:
* A crystal is attached between the XTAL1 and XTAL2 pins. * A clock is driven into the XTAL1 pin, with the XTAL2 pin left floating.
For details on CLOCK usage, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1".
7.9.17 GND (die pad)
Global ground signal, except for the charge pump that uses CPGND. The die pad is exposed on the underside of the package as a ground plate. This acts as a ground to all circuits in the ISP1506, except the charge pump. To ensure correct operation of the ISP1506, GND must be soldered to the cleanest ground available.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
14 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
8. Modes of operation
8.1 ULPI modes
The ISP1506 ULPI bus can be programmed to operate in three modes. Each mode reconfigures the signals on the data bus as described in the following subsections. Setting more than one mode will lead to undefined behavior.
8.1.1 Synchronous mode
This is default mode. At power-up, and when CLOCK is stable, the ISP1506 will enter synchronous mode. The link must synchronize all ULPI signals to CLOCK, meeting the set-up and hold times as defined in Section 15. A description of the ULPI pin behavior in synchronous mode is given in Table 4. This mode is used by the link to perform the following tasks:
* * * *
High-speed detection handshake (chirp) Transmit and receive USB packets Read and write to registers Receive USB status updates (RXCMDs)
For more information on the various synchronous mode protocols, see Section 9.
Table 4. ULPI signal description Direction on Signal description ISP1506 I/O I/O 60 MHz interface clock. If a crystal is attached or a clock is driven into the XTAL1 pin, the ISP1506 will drive a 60 MHz output clock. 4-bit data bus. In synchronous mode, the link drives DATA[3:0] to LOW by default. The link initiates transfers by sending a nonzero data pattern called TXCMD (transmit command). In synchronous mode, the direction of DATA[3:0] is controlled by DIR. Contents of DATA[3:0] lines must be ignored for exactly one clock cycle whenever DIR changes value. This is called the turnaround cycle. Bytes of data are transferred between the link and PHY in 4-bit nibbles. The least significant nibble, DATA[3:0], is transferred first on the rising edge of clock. The most significant nibble, DATA[7:4], is transferred next on the falling edge of clock. Transferring an odd number of 4-bit nibbles is not allowed. Data lines have fixed direction and different meaning in low-power and 3-pin serial modes.
Signal name CLOCK DATA[3:0]
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
15 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 4.
ULPI signal description ...continued Direction on Signal description ISP1506 O Direction: Controls the direction of data bus DATA[3:0]. In synchronous mode, the ISP1506 drives DIR to LOW by default, making the data bus an input so that the ISP1506 can listen for TXCMDs from the link. The ISP1506 drives DIR to HIGH only when it has data for the link. When DIR and NXT are HIGH, the byte on the data bus contains decoded USB data. When DIR is HIGH and NXT is LOW, the byte contains status information called RXCMD (receive command). The only exception to this rule is when the PHY returns register read data, where NXT is also LOW, replacing the usual RXCMD byte. Every change in DIR causes a turnaround cycle on the data bus, during which DATA[3:0] is not valid and must be ignored by the link. DIR is always asserted during low-power and 3-pin serial modes. Stop: In synchronous mode, the link drives STP to HIGH for one cycle after the last byte of data is sent to the ISP1506. The link can optionally assert STP to force DIR to be deasserted. In low-power and 3-pin serial modes, the link holds STP at HIGH to wake up the ISP1506, causing the ULPI bus to return to synchronous mode.
Signal name DIR
STP
I
NXT
O
Next: In synchronous mode, the ISP1506 drives NXT to HIGH to throttle data. If DIR is LOW, the ISP1506 asserts NXT to notify the link to place the next data byte on DATA[3:0] in the following clock cycle. If DIR is HIGH, the ISP1506 asserts NXT to notify the link that a valid USB data byte is on DATA[3:0] in the current cycle. The ISP1506 always drives an RXCMD when DIR is HIGH and NXT is LOW, unless register read data is to be returned to the link in the current cycle. NXT is not used in low-power or 3-pin serial modes.
8.1.2 Low-power mode
When the USB is idle, the link can place the ISP1506 into low-power mode (also called suspend mode). In low-power mode, the data bus definition changes to that shown in Table 5. To enter low-power mode, the link sets the SUSPENDM bit in the Function Control register to logic 0. To exit low-power mode, the link asserts the STP signal. The ISP1506 will draw only suspend current from the VCC supply (see Table 45). During low-power mode, the clock on XTAL1 may be stopped. The clock must be started again before asserting STP to exit low-power mode. After exiting low-power mode, the ISP1506 will send an RXCMD to the link if a change was detected in any interrupt source, and the change still exists. An RXCMD may not be sent if the interrupt condition is removed before exiting. For more information on low-power mode enter and exit protocols, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1".
Table 5. Signal LINESTATE0 LINESTATE1 Reserved INT Signal mapping during low-power mode Maps to DATA0 DATA1 DATA2 DATA3 Direction O O O O Description combinatorial LINESTATE0 directly driven by the analog receiver combinatorial LINESTATE1 directly driven by the analog receiver reserved; the ISP1506 will drive this pin to LOW active HIGH interrupt indication; will be asserted whenever any unmasked interrupt occurs
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
16 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
8.1.3 3-pin full-speed or low-speed serial mode
If the link requires a 3-pin serial interface to transmit and receive full-speed or low-speed USB data, it can set the ISP1506 to 3-pin serial mode. In 3-pin serial mode, the data bus definition changes to that shown in Table 6. To enter 3-pin serial mode, the link sets the 3PIN_FSLS_SERIAL bit in the Interface Control register to logic 1. To exit 3-pin serial mode, the link asserts STP. This is primarily provided for links that contain legacy full-speed or low-speed functionality, providing a more cost-effective upgrade path to high-speed. An interrupt pin is also provided to inform the link of USB events. If the link requires CLOCK to be running during 3-pin serial mode, the CLOCK_SUSPENDM register bit must be set to logic 1. For more information on 3-pin serial mode enter and exit protocols, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1".
Table 6. Signal TX_ENABLE DAT SE0 INT Signal mapping for 3-pin serial mode Maps to DATA0 DATA1 DATA2 DATA3 Direction I I/O I/O O Description active HIGH transmit enable transmit differential data on DP and DM when TX_ENABLE is HIGH receive differential data from DP and DM when TX_ENABLE is LOW transmit single-ended zero on DP and DM when TX_ENABLE is HIGH receive single-ended zero from DP and DM when TX_ENABLE is LOW active HIGH interrupt indication; will be asserted whenever any unmasked interrupt occurs
8.2 USB and OTG state transitions
A Hi-Speed USB peripheral, host or OTG device handles more than one electrical state as defined in Ref. 1 "Universal Serial Bus Specification Rev. 2.0" and Ref. 2 "On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3". The ISP1506 accommodates various states through register bit settings of XCVRSELECT[1:0], TERMSELECT, OPMODE[1:0], DP_PULLDOWN and DM_PULLDOWN. Table 7 summarizes operating states. The values of register settings in Table 7 will force resistor settings as also given in Table 7. Resistor setting signals are defined as follows:
* * * *
RPU_DP_EN enables the 1.5 k pull-up resistor on DP RPD_DP_EN enables the 15 k pull-down resistor on DP RPD_DM_EN enables the 15 k pull-down resistor on DM HSTERM_EN enables the 45 termination resistors on DP and DM
The link is responsible for setting the desired USB and OTG states.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
17 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 7.
Operating states and their corresponding resistor settings Register settings XCVR SELECT [1:0] TERM SELECT OPMODE [1:0] Internal resistor settings DP_PULL DM_PULL RPU_ DOWN DOWN DP_EN RPD_ DP_EN RPD_ HSTERM DM_EN _EN
Signaling mode
General settings 3-state drivers Power-up or VBUS < VB_SESS_END Host settings Host chirp Host high-speed Host full-speed Host high-speed or full-speed suspend Host high-speed or full-speed resume Host low-speed Host low-speed suspend Host low-speed resume Peripheral settings Peripheral chirp Peripheral high-speed Peripheral high-speed or full-speed suspend Peripheral high-speed or full-speed resume Peripheral Test J or Test K OTG settings OTG device peripheral chirp OTG device peripheral high-speed 00b 00b 1b 0b 10b 00b 0b 0b 1b 1b 1b 0b 0b 0b 1b 1b 0b 1b 00b 00b 1b 0b 1b 1b 10b 00b 00b 00b 0b 0b 0b 0b 0b 0b 0b 0b 1b 0b 1b 1b 0b 0b 0b 0b 0b 0b 0b 0b 0b 1b 0b 0b 00b 00b X1b 01b 01b 10b 10b 10b 0b 0b 1b 1b 1b 1b 1b 1b 0b 10b 00b 00b 00b 10b 00b 00b 10b 10b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 0b 0b 0b 0b 0b 0b 0b 0b 0b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 0b 0b 0b 0b 0b 0b 1b XXb 01b Xb 0b 01b 00b Xb 1b Xb 1b 0b 0b 0b 1b 0b 1b 0b 0b
Host Test J or Test K 00b
Peripheral full-speed 01b 01b
01b
1b
10b
0b
0b
1b
0b
0b
0b
00b
0b
10b
0b
0b
0b
0b
0b
1b
OTG device 01b peripheral full-speed
1b
00b
0b
1b
1b
0b
1b
0b
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
18 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 7.
Operating states and their corresponding resistor settings ...continued Register settings XCVR SELECT [1:0] TERM SELECT 1b OPMODE [1:0] 00b Internal resistor settings DP_PULL DM_PULL RPU_ DOWN DOWN DP_EN 0b 1b 1b RPD_ DP_EN 0b RPD_ HSTERM DM_EN _EN 1b 0b
Signaling mode
OTG device peripheral high-speed and full-speed suspend OTG device peripheral high-speed and full-speed resume OTG device peripheral Test J or Test K
01b
01b
1b
10b
0b
1b
1b
0b
1b
0b
00b
0b
10b
0b
1b
0b
0b
1b
1b
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
19 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
9. Protocol description
The following subsections describe the protocol for using the ISP1506. Remark: In all figures, the ULPI data is shown in a generic form and not as nibbles on the rising and falling edges of the clock.
9.1 ULPI references
The ISP1506 provides an 8-pin ULPI interface to communicate with the link. It is highly recommended that you read Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1" and Ref. 4 "UTMI+ Specification Rev. 1.0".
9.2 Power-On Reset (POR)
An internal POR is generated when REG1V8 rises above VPOR(trip), for at least tw(REG1V8_H). The internal POR pulse will also be generated whenever REG1V8 drops below VPOR(trip) for more than tw(REG1V8_L), and then rises above VPOR(trip) again. The voltage on REG1V8 is generated from VCC. To give a better view of the functionality, Figure 5 shows a possible curve of REG1V8. The internal POR starts with logic 0 at t0. At t1, the detector will see the passing of the trip level so that POR turns to logic 1 and a delay element will add another tPORP before it drops to logic 0. If REG1V8 dips from t2 to t3 for > tw(REG1V8_L), another POR pulse is generated. If the dip at t4 to t5 is too short, that is, < tw(REG1V8_L), the internal POR pulse will not react and will remain LOW.
REG1V8 VPOR(trip)
t0
t1 tPORP
t2
t3 tPORP
t4
t5 POR
004aaa751
Fig 5.
Internal power-on reset timing
9.3 Power-up, reset and bus idle sequence
Figure 6 shows a typical start-up sequence. On power-up, the ISP1506 performs an internal power-on reset and asserts DIR to indicate to the link that the ULPI bus cannot be used. When the internal PLL is stable, the ISP1506 deasserts DIR. The power-up time depends on the VCC supply rise time, the crystal start-up time, and PLL start-up time tstartup(o)(CLOCK). Whenever DIR is asserted, the ISP1506 drives the NXT pin to LOW and drives DATA[3:0] with RXCMD values. When DIR is deasserted, the link must drive the data bus to a valid level. By default, the link must drive data to LOW. When the ISP1506 initially deasserts DIR on power-up, the link must ignore all RXCMDs until it resets the ISP1506. Before beginning USB packets, the link must set the RESET bit in the Function Control register to reset the ISP1506. After the RESET bit is set, the ISP1506 will assert DIR until the internal reset completes. The ISP1506 will automatically deassert DIR and clear the RESET bit when reset has
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
20 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
completed. After every reset, an RXCMD is sent to the link to update USB status information. After this sequence, the ULPI bus is ready for use and the link can start USB operations. When the internal PLL is stable, the ISP1506 will drive a 60 MHz clock out from the CLOCK pin when DIR deasserts. An example start-up sequence is shown in Figure 6. The recommended power-up sequence for the link is as follows: 1. The link waits for 1 ms, ignoring all the ULPI pin status. 2. The link may start to detect DIR status level. If DIR is detected as LOW for three clock cycles, the link may send a RESET command. The ULPI interface is ready for use.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
21 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
VCC
VCC(I/O) REG1V8 tPWRUP internal REG1V8 detector internal POR
XTAL1 internal clocks stable CLOCK tstartup(PLL) bus idle
RESET command DATA[3:0] TXCMD D internal reset DIR STP RXCMD update
NXT t1 t2 t3 t4 t5
004aaa886
t1 = VCC and VCC(I/O) are applied to the ISP1506. The ISP1506 regulator starts to turn on. t2 = ULPI pads detect REG1V8 rising above the REG1V8 regulator threshold and are not in 3-state. These pads may drive either LOW or HIGH. It is recommended that the link ignores the ULPI pins status during tPWRUP. t3 = The POR threshold is reached and a POR pulse is generated. After the POR pulse, ULPI pins are driven to a defined level. DIR is driven to HIGH and the other pins are driven to LOW. t4 = The internal PLL is stabilized after tstartup(PLL). If the 19.2 MHz or 26 MHz clock is started before POR, the internal PLL will be stabilized after tstartup(PLL) from POR. The CLOCK pin starts to output 60 MHz. The DIR pin will transition from HIGH to LOW. The DIR pin will remain LOW before the link issues a RESET command to the ISP1506. t5 = The power-up sequence is completed and the ULPI bus interface is ready for use.
Fig 6.
Power-up and reset sequence required before the ULPI bus is ready for use
9.3.1 Interface protection
By default, the ISP1506 enables a weak pull-up resistor on STP. If the STP pin is unexpectedly HIGH at any time, the ISP1506 will protect the ULPI interface by enabling weak pull-down resistors on DATA[3:0].
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
22 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
The interface protect feature prevents unwanted activity of the ISP1506 whenever the ULPI interface is not correctly driven by the link. For example, when the link powers up more slowly than the ISP1506. The interface protect feature can be disabled by setting the INTF_PROT_DIS bit to logic 1.
9.3.2 Interface behavior with respect to RESET_N
The use of the RESET_N pin is optional. When RESET_N is asserted (LOW), the ISP1506 will assert DIR. All logic in the ISP1506 will be reset, including the analog circuitry and ULPI registers. During reset, the link must drive DATA[3:0] and STP to LOW; otherwise undefined behavior may result. When RESET_N is deasserted (HIGH), the DIR output will deassert (LOW) four or five clock cycles later. Figure 7 shows the ULPI interface behavior when RESET_N is asserted (LOW), and subsequently deasserted (HIGH). If RESET_N is not used, it must be connected to VCC(I/O).
CLOCK
RESET_N
DATA[3:0]
Hi-Z (input)
Hi-Z (link must drive)
Hi-Z (input)
DIR
STP
Hi-Z (input)
Hi-Z (link must drive)
Hi-Z (input)
NXT
004aaa890
Fig 7.
Interface behavior with respect to RESET_N
9.4 VBUS power and fault detection
9.4.1 Driving 5 V on VBUS
The ISP1506 provides a built-in charge pump. To enable the charge pump, the link must set the DRV_VBUS bit in the OTG Control register. The ISP1506 also supports external 5 V supplies. The ISP1506 can control the external supply using the active-LOW PSW_N open-drain output pin. To enable the external supply by driving PSW_N to LOW, the link must set the DRV_VBUS_EXT bit in the OTG Control register to logic 1. The link can optionally set both the DRV_VBUS and DRV_VBUS_EXT bits to logic 1 to enable the external supply. Table 8 summarizes settings to drive 5 V on VBUS.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
23 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
OTG Control register power control bits DRV_VBUS_EXT 0 0 1 Power source used internal and external VBUS power sources are disabled internal VBUS charge pump is enabled external 5 V VBUS supply is enabled
Table 8. 0 1 X
DRV_VBUS
9.4.2 Fault detection
The ISP1506 supports external VBUS fault detector circuits that output a digital fault indicator signal. The indicator signal must be connected to the FAULT pin. To enable the ISP1506 to monitor the digital fault input, the link must set the USE_EXT_VBUS_IND bit in the OTG Control register and the IND_PASSTHRU bit in the Interface Control register to logic 1. For details, see Figure 9. The FAULT input pin is mapped to the A_VBUS_VLD bit in RXCMD. Any changes for the FAULT input will trigger RXCMD carrying the FAULT condition with A_VBUS_VLD.
9.5 TXCMD and RXCMD
Commands between the ISP1506 and the link are described in the following subsections.
9.5.1 TXCMD
By default, the link must drive the ULPI bus to its idle state of 00h. To send commands and USB packets, the link drives a nonzero value on DATA[3:0] to the ISP1506 by sending a byte called TXCMD. Commands include USB packet transmissions, and register reads and writes. Once the TXCMD is interpreted and accepted by the ISP1506, the NXT signal is asserted and the link can follow up with the required number of data bytes. The TXCMD byte format is given in Table 9. Any values other than those in Table 9 are illegal and may result in undefined behavior. Various TXCMD packet and register sequences are shown in later sections.
Table 9. Command type name Idle Packet transmit TXCMD byte format Command code 00b 01b Command payload 00 0000b 00 0000b Command name NOOP NOPID Command description No operation. 00h is the idle value of the data bus. The link must drive NOOP by default. Transmit USB data that does not have a PID, such as chirp and resume signaling. The ISP1506 starts transmitting only after accepting the next data byte. Transmit USB packet. DATA[3:0] indicates USB packet identifier PID[3:0]. Extended register write command (optional). The 8-bit address must be provided after the command is accepted. Register write command with 6-bit immediate address. Extended register read command (optional). The 8-bit address must be provided after the command is accepted. Register read command with 6-bit immediate address.
00 XXXXb Register write 10b 10 1111b
PID EXTW
XX XXXXb Register read 11b 10 1111b
REGW EXTR
XX XXXXb
REGR
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
24 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
9.5.2 RXCMD
The ISP1506 communicates status information to the link by asserting DIR and sending an RXCMD byte on the data bus. The RXCMD data byte format is given in Table 10. The ISP1506 will automatically send an RXCMD whenever there is a change in any of the RXCMD data fields. The link must be able to accept an RXCMD at any time; including single RXCMDs, back-to-back RXCMDs, and RXCMDs at any time during USB receive packets when NXT is LOW. An example is shown in Figure 8. For details and diagrams, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1". An RXCMD may not be sent when exiting low-power mode or serial mode, if the interrupt condition is removed before exiting.
Table 10. DATA 1 to 0 RXCMD byte format Name Description and value DATA0 -- LINESTATE[0] DATA1 -- LINESTATE[1] 3 to 2 5 to 4 6 7 VBUS state RxEvent ID ALT_INT Encoded VBUS voltage state: For an explanation of the VBUS state, see Section 9.5.2.2. Encoded USB event signals: For an explanation of RxEvent, see Section 9.5.2.4. Set to the value of the ID pin. By default, this signal is not used and is not needed in typical designs. Optionally, the link can enable the BVALID_RISE and/or BVALID_FALL bits in the Power Control register. Corresponding changes in BVALID will cause an RXCMD to be sent to the link with the ALT_INT bit asserted. LINESTATE LINESTATE signals: For a definition of LINESTATE, see Section 9.5.2.1.
CLOCK single RXCMD DATA[ 3:0] turnaround RXCMD turnaround turnaround back-to-back RXCMDs RXCMD RXCMD turnaround
DIR STP NXT
004aaa760
Fig 8.
Single and back-to-back RXCMDs from the ISP1506 to the link
9.5.2.1
Linestate encoding LINESTATE[1:0] reflects the current state of DP and DM. Whenever the ISP1506 detects a change in DP or DM, an RXCMD will be sent to the link with the new LINESTATE[1:0] value. The value given on LINESTATE[1:0] depends on the setting of various registers. Table 11 shows the LINESTATE[1:0] encoding for upstream facing ports, which applies to peripherals. Table 12 shows the LINESTATE[1:0] encoding for downstream facing ports, which applies to host controllers. Dual-role devices must choose the correct table, depending on whether it is in peripheral or host mode.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
25 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 11. LINESTATE[1:0] encoding for upstream facing ports: peripheral DP_PULLDOWN = 0.[1] Mode XCVRSELECT[1:0] TERMSELECT LINESTATE[1:0] 00 01 10 11
[1]
Full-speed 01, 11 1 SE0 FS-J FS-K SE1
High-speed 00 0 squelch !squelch invalid invalid
Chirp 00 1 squelch !squelch and HS_Differential_Receiver_Output !squelch and !HS_Differential_Receiver_Output invalid
!squelch indicates inactive squelch. !HS_Differential_Receiver_Output indicates inactive HS_Differential_Receiver_Output.
Table 12. LINESTATE[1:0] encoding for downstream facing ports: host DP_PULLDOWN and DM_PULLDOWN = 1.[1] Mode XCVRSELECT[1:0] TERMSELECT OPMODE[1:0] LINESTATE[1:0] 00 01 10 11
[1]
Low-speed 10 1 X SE0 LS-K LS-J SE1
Full-speed 01, 11 1 X SE0 FS-J FS-K SE1
High-speed 00 0 00, 01 or 11 squelch !squelch invalid invalid
Chirp 00 0 10 squelch !squelch and HS_Differential_Receiver_Output !squelch and !HS_Differential_Receiver_Output invalid
!squelch indicates inactive squelch. !HS_Differential_Receiver_Output indicates inactive HS_Differential_Receiver_Output.
9.5.2.2
VBUS state encoding USB devices must monitor the VBUS voltage for purposes such as overcurrent detection, starting a session and SRP. The VBUS state field in the RXCMD is an encoding of the voltage level on VBUS. The A_VBUS_VLD, SESS_VLD and SESS_END indicators in the VBUS state are directly taken from internal comparators built-in to the ISP1506, and encoded as shown in Table 10 and Table 13.
Table 13. Value 00 01 10 11 Encoded VBUS voltage state VBUS voltage VBUS < VB_SESS_END VB_SESS_END VBUS < VB_SESS_VLD VB_SESS_VLD VBUS < VA_VBUS_VLD VBUS VA_VBUS_VLD SESS_END 1 0 X X SESS_VLD 0 0 1 X A_VBUS_VLD 0 0 0 1
For high-power USB hosts supplying more than 100 mA, it is recommended that you use an external FAULT indicator. Internal comparators must not be used. Note that VBUS and FAULT share the same pin and cannot be used simultaneously. A_VBUS_VLD and FAULT will be interpreted by the ISP1506 as shown in Figure 9. A description on how to use and select the VBUS state encoding is given in Section 9.5.2.3.
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
26 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
A_VBUS_VLD comparator (VBUS < 4.4 V) VBUS/FAULT internal A_VBUS_VLD (0, X) RXCMD A_VBUS_VLD complement output (1, 1)
IND_COMPL
USE_EXT_VBUS_IND, IND_PASSTHRU
004aaa752
Fig 9.
RXCMD A_VBUS_VLD indicator source
9.5.2.3
Using and selecting the VBUS state encoding The VBUS state encoding is shown in Table 13. The ISP1506 will send an RXCMD to the link whenever there is a change in the VBUS state. To receive VBUS state updates, the link must first enable the corresponding interrupts in the USB Interrupt Enable Rising Edge and USB Interrupt Enable Falling Edge registers. The link can use the VBUS state to monitor VBUS and take appropriate action. Table 14 shows the recommended usage for typical applications.
Table 14. VBUS indicators in RXCMD required for typical applications A_VBUS_VLD yes no yes no SESS_VLD no yes yes yes SESS_END no no no yes
Application Standard host Standard peripheral OTG A-device OTG B-device
Standard USB host controllers: For standard hosts, the system must be able to provide 500 mA on VBUS in the range of 4.75 V to 5.25 V. An external circuit must be used to detect overcurrent conditions. If the external overcurrent detector provides a digital fault signal, then the fault signal must be connected to the ISP1506 FAULT input pin, and the link must do the following: 1. Set the IND_COMPL bit in the Interface Control register to logic 0 or logic 1, depending on the polarity of the external fault signal. 2. Set the USE_EXT_VBUS_IND bit in the OTG Control register to logic 1. 3. Set the IND_PASSTHRU bit in the Interface Control register to logic 1 (mandatory). Standard USB peripheral controllers: Standard peripherals must be able to detect when VBUS is at a sufficient level for operation. SESS_VLD must be enabled to detect the start and end of USB peripheral operations. Detection of A_VBUS_VLD and SESS_END thresholds is not needed for standard peripherals.
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
27 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
OTG devices: When an OTG device is configured as an OTG A-device, it must be able to provide a minimum of 8 mA on VBUS. If the OTG A-device provides less than 100 mA, then there is no need for an overcurrent detection circuit because the internal A_VBUS_VLD comparator is sufficient. If the OTG A-device provides more than 100 mA on VBUS, an overcurrent detector must be used and Section "Standard USB host controllers" applies. The OTG A-device also uses SESS_VLD to detect when an OTG B-device is initiating VBUS pulsing SRP. When an OTG device is configured as an OTG B-device, SESS_VLD must be used to detect when VBUS is at a sufficient level for operation. SESS_END must be used to detect when VBUS has dropped to a LOW level, allowing the B-device to safely initiate VBUS pulsing SRP. 9.5.2.4 RxEvent encoding The RxEvent field (see Table 15) of the RXCMD informs the link of information related packets received on the USB bus. RxActive and RxError are defined in Ref. 5 "USB 2.0 Transceiver Macrocell Interface (UTMI) Specification Ver. 1.05". HostDisconnect is defined in Ref. 4 "UTMI+ Specification Rev. 1.0". A short definition is also given in the following subsections.
Table 15. Value 00 01 11 10 Encoded USB event signals RxActive 0 1 1 X RxError 0 0 1 X HostDisconnect 0 0 0 1
RxActive: When the ISP1506 has detected a SYNC pattern on the USB bus, it signals an RxActive event to the link. An RxActive event can be communicated using two methods. The first method is for the ISP1506 to simultaneously assert DIR and NXT. The second method is for the ISP1506 to send an RXCMD to the link with the RxActive field in RxEvent bits set to logic 1. The link must be able to detect both methods. RxActive frames the receive packet from the first byte to the last byte. The link must assume that RxActive is set to logic 0 when indicated in an RXCMD or when DIR is deasserted, whichever occurs first. The link uses RxActive to time high-speed packets and ensure that bus turnaround times are met. For more information on the USB packet timing, see Section 9.8.1. RxError: When the ISP1506 has detected an error while receiving a USB packet, it deasserts NXT and sends an RXCMD with the RxError field set to logic 1. The received packet is no longer valid and must be dropped by the link. HostDisconnect: HostDisconnect is encoded into the RxEvent field of the RXCMD. HostDisconnect is valid only when the ISP1506 is configured as a host (both DP_PULLDOWN and DM_PULLDOWN are set to logic 1), and indicates to the host controller when a peripheral is connected or disconnected. The host controller must enable HostDisconnect by setting the HOST_DISCON_R and HOST_DISCON_F bits in the USB Interrupt Enable Rising Edge and USB Interrupt Enable Falling Edge registers, respectively. Changes in HostDisconnect will cause the PHY to send an RXCMD to the link with the updated value.
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
28 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
9.6 Register read and write operations
Figure 10 shows the register read and write sequences. The ISP1506 supports immediate addressing and extended addressing register operations. Extended register addressing is optional for links. Note that register operations will be aborted if the ISP1506 unexpectedly asserts DIR during the operation. When a register operation is aborted, the link must retry until successful. For more information on register operations, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1".
CLOCK TXCMD (REGW) D DATA[3:0] TXCMD (EXTW) AD D TXCMD (REGR) TXCMD (EXTW) AD
D
D
immediate register write DIR
extended register write
immediate register read
extended register read
STP
NXT
004aaa761
AD indicates the address byte, and D indicates the data byte.
Fig 10. Example of register write, register read, extended register write and extended register read
9.7 USB reset and high-speed detection handshake (chirp)
Figure 11 shows the sequence of events for USB reset and high-speed detection handshake (chirp). The sequence is shown for hosts and peripherals. Figure 11 does not show all RXCMD updates, and timing is not to scale. The sequence is as follows: 1. USB reset: The host detects a peripheral attachment as low-speed if DM is HIGH and as full-speed if DP is HIGH. If a host detects a low-speed peripheral, it does not follow the remainder of this protocol. If a host detects a full-speed peripheral, it resets the peripheral by writing to the Function Control register and setting XCVRSELECT[1:0] = 00b (high-speed) and TERMSELECT = 0b, which drives SE0 on the bus (DP and DM connected to ground through 45 ). The host also sets OPMODE[1:0] = 10b for correct chirp transmit and receive. The start of SE0 is labeled T0. Remark: To receive chirp signaling, the host must also consider the high-speed differential receiver output. The host controller must interpret LINESTATE[1:0] as shown in Table 12. 2. High-speed detection handshake (chirp) a. Peripheral chirp: After detecting SE0 for no less than 2.5 s, if the peripheral is capable of high-speed, it sets XCVRSELECT[1:0] = 00b (high-speed) and OPMODE[1:0] = 10b (chirp). The peripheral immediately follows this with a TXCMD (NOPID), transmitting a Chirp K for no less than 1 ms and ending no more
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
29 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver than 7 ms after reset time T0. If the peripheral is in low-power mode, it must wake up its clock within 5.6 ms, leaving 200 s for the link to start transmitting the Chirp K, and 1.2 ms for the Chirp K to complete (worst case with 10 % slow clock).
b. Host chirp: If the host does not detect the peripheral chirp, it must continue asserting SE0 until the end of reset. If the host detects the peripheral Chirp K for no less than 2.5 s, then no more than 100 s after the bus leaves the Chirp K state, the host sends a TXCMD (NOPID) with an alternating sequence of Chirp Ks and Chirp Js. Each Chirp K or Chirp J must last no less than 40 s and no longer than 60 s. c. High-speed idle: The peripheral must detect a minimum of Chirp K-J-K-J-K-J. Each Chirp K and Chirp J must be detected for at least 2.5 s. After seeing that minimum sequence, the peripheral sets TERMSELECT = 0b and OPMODE[1:0] = 00b. The peripheral is now in high-speed mode and sees !squelch (01b on LINESTATE). When the peripheral sees squelch (10b on LINESTATE), it knows that the host has completed chirp and waits for Hi-Speed USB traffic to begin. After transmitting the chirp sequence, the host changes OPMODE[1:0] to 00b and begins sending USB packets. For more information, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1".
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
30 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
USB reset T0 TXCMD (REGW) SE0 DATA [ 3:0] DIR STP
high-speed detection handshake (chirp) peripheral chirp TXCMD NOPID K host chirp TXCMD J (REGW) HS idle
K
00
J
...
K
ULPI host
NXT 01 (FS) XCVR SELECT TERM SELECT 00 (normal) OP MODE J (01b) LINE STATE TXCMD TXCMD SE0 (REGW) NOPID K DATA [ 3:0] DIR STP RXCMDs K ... K 00 K J K J K TXCMD J (REGW) SE0 (00b) peripheral chirp K (10b) squelch (00b) host chirp K (10b) or chirp J (01b) squelch (00b) 01 (chirp) 00 (normal) 00 (HS)
00
ULPI peripheral
NXT 01 (FS) XCVR SELECT TERM SELECT 00 (normal) OP MODE squelch (00b) !squelch (01b) squelch (00b) 10 (chirp) 00 (normal) 00 (HS)
J (01b) LINE STATE USB signals
SE0 (00b)
peripheral chirp K (10b)
host chirp K or J (10b or 01b)
DP
DM
004aaa762
Timing is not to scale.
Fig 11. USB reset and high-speed detection handshake (chirp) sequence
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
31 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
9.8 USB packet transmit and receive
An example of a packet transmit and receive is shown in Figure 12. For details on USB packets, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1".
link sends TXCMD
ISP1506 accepts TXCMD
link sends the next data; ISP1506 link signals accepts end of data
ISP1506 ISP1506 ISP1506 deasserts asserts DIR, ISP1506 sends sends DIR, causing causing RXCMD ULPI bus turnaround USB data turnaround (NXT LOW) (NXT HIGH) is idle cycle cycle
CLOCK
DATA[ 3:0]
TXCMD
DATA
turnaround
RXCMD
DATA
turnaround
DIR
STP
NXT
004aaa763
Fig 12. Example of using the ISP1506 to transmit and receive USB data
9.8.1 USB packet timing
9.8.1.1 ISP1506 pipeline delays The ISP1506 delays are shown in Table 16. For detailed description, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1", Section 3.8.2.6.2.
Table 16. PHY pipeline delays High-speed PHY delay 4 4 1 to 2 3 to 4 6 to 9 5 to 6 5 to 6 Full-speed PHY delay 4 4 to 6 6 to 10 not applicable not applicable not applicable 17 to 18 Low-speed PHY delay 4 16 to 18 74 to 75 not applicable not applicable not applicable 122 to 123
Parameter name RXCMD delay (J and K) RXCMD delay (SE0) TX start delay TX end delay (packets) TX end delay (SOF) RX start delay RX end delay
9.8.1.2
Allowed link decision time The amount of clock cycles allocated to the link to respond to a received packet and correctly receive back-to-back packets is given in Table 17. Link designs must follow values given in Table 17 for correct USB system operation. Examples of high-speed packet sequences and timing are shown in Figure 13 and Figure 14. For details, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1", Section 3.8.2.6.3.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
32 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 17.
Link decision times
Packet sequence High-speed Full-speed Low-speed Definition link delay link delay link delay Transmit-Transmit (host only) 15 to 24 7 to 18 77 to 247 Number of clocks a host link must wait before driving the TXCMD for the second packet. In high-speed, the link starts counting from the assertion of STP for the first packet. In full-speed, the link starts counting from the RXCMD, indicating LINESTATE has changed from SE0 to J for the first packet. The timing given ensures inter-packet delays of 2 bit times to 6.5 bit times. Receive-Transmit (host or peripheral) 1 to 14 7 to 18 77 to 247 Number of clocks the link must wait before driving the TXCMD for the transmit packet. In high-speed, the link starts counting from the end of the receive packet; deassertion of DIR or an RXCMD indicating RxActive is LOW. In full-speed or low-speed, the link starts counting from the RXCMD, indicating LINESTATE has changed from SE0 to J for the receive packet. The timing given ensures inter-packet delays of 2 bit times to 6.5 bit times. Receive-Receive (peripheral only) Transmit-Receive (host or peripheral) 1 92 1 80 1 718 Minimum number of clocks between consecutive receive packets. The link must be able to receive both packets. Host or peripheral transmits a packet and will time-out after this number of clock cycles if a response is not received. Any subsequent transmission can occur after this time.
USB interpacket delay (88 to 192 high-speed bit times) DP or DM CLOCK DN-1 DATA [3:0] DIR DN TXCMD D0 D1
DATA
EOP
IDLE
SYNC
STP
NXT
link decision time (15 to 24 clocks) TX end delay (two to five clocks) TX start delay (one to two clocks)
004aaa891
Fig 13. High-speed transmit-to-transmit packet timing
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
33 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
USB interpacket delay (8 to 192 high-speed bit times) DP or DM
DATA
EOP
IDLE
SYNC
CLOCK
DN-4 DATA [3:0] DN-3 DIR STP
DN-2
DN
TXCMD
D0
D1
DN-1
turnaround
NXT
RX end delay (three to eight clocks)
link decision time (1 to 14 clocks)
TX start delay (one to two clocks)
004aaa892
Fig 14. High-speed receive-to-transmit packet timing
9.9 Preamble
Preamble packets are headers to low-speed packets that must travel over a full-speed bus, between a host and a hub. To enter preamble mode, the link sets XCVRSELECT[1:0] = 11b in the Function Control register. When in preamble mode, the ISP1506 operates just as in full-speed mode, and sends all data with the full-speed rise time and fall time. Whenever the link transmits a USB packet in preamble mode, the ISP1506 will automatically send a preamble header at full-speed bit rate before sending the link packet at low-speed bit rate. The ISP1506 will ensure a minimum gap of four full-speed bit times between the last bit of the full-speed PRE PID and the first bit of the low-speed packet SYNC. The ISP1506 will drive a J for at least one full-speed bit time after sending the PRE PID, after which the pull-up resistor can hold the J state on the bus. An example transmit packet is shown in Figure 15. In preamble mode, the ISP1506 can also receive low-speed packets from the full-speed bus.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
34 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
CLOCK
DATA[3:0] DIR STP
TXCMD (low-speed packet ID)
D0
D1
NXT
DP or DM
FS SYNC
FS PRE ID
IDLE (min 4 FS bits)
LS SYNC
LS PID
LS D0
LS D1
004aaa764
DP and DM timing is not to scale.
Fig 15. Preamble sequence
9.10 USB suspend and resume
9.10.1 Full-speed or low-speed host-initiated suspend and resume
Figure 16 illustrates how a host or a hub places a full-speed or low-speed peripheral into suspend and sometime later initiates resume signaling to wake up the downstream peripheral. Note that Figure 16 timing is not to scale, and does not show all RXCMD LINESTATE updates. The sequence of events for a host and a peripheral, both with ISP1506, is as follows. 1. Idle: Initially, the host and the peripheral are idle. The host has its 15 k pull-down resistors enabled (DP_PULLDOWN and DM_PULLDOWN are set to 1b), and 45 terminations disabled (TERMSELECT is set to 1b). The peripheral has the 1.5 k pull-up resistor connected to DP for full-speed or DM for low-speed (TERMSELECT is set to 1b). 2. Suspend: When the peripheral sees no bus activity for 3 ms, it enters the suspend state. The peripheral link places the PHY into low-power mode by clearing the SUSPENDM bit in the Function Control register, causing the PHY to draw only suspend current. The host may or may not be powered down. 3. Resume K: When the host wants to wake up the peripheral, it sets OPMODE[1:0] to 10b and transmits a K for at least 20 ms. The peripheral link sees the resume K on LINESTATE, and asserts STP to wake up the PHY. 4. EOP: When STP is asserted, the ISP1506 on the host side automatically appends an EOP of two bits of SE0 at low-speed bit rate, followed by one bit of J. The ISP1506 on the host side knows to add the EOP because DP_PULLDOWN and DM_PULLDOWN are set to 1b for a host. After the EOP is completed, the host link sets OPMODE[1:0] to 00b for normal operation. The peripheral link sees the EOP and also resumes normal operation.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
35 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
idle
suspend TXCMD (REGW) TXCMD NOPID
resume K K K ... K
EOP TXCMD
idle
FS or LS host (XCVRSELECT = 01b (FS) or 10b (LS), DP_PULLDOWN = 1b, DM_PULLDOWN = 1b, TERMSELECT = 1b)
DATA [ 3:0] DIR STP NXT OPMODE
00b
10b
00b
LINE STATE
J
K
SE0
J
CLOCK FS or LS peripheral (XCVRSELECT = 01b (FS) or 10b (LS), DP_PULLDOWN = 0b, TERMSELECT = 1b) TXCMD (REGW) DATA [ 3:0] DIR
LINESTATE J
LINESTATE K
SE0
J
STP NXT
OPMODE
00b
10b
00b
SUSPENDM
LINE STATE USB signals (only FS is shown)
J
K
SE0
J
DP
DM
004aaa765
Timing is not to scale.
Fig 16. Full-speed suspend and resume
9.10.2 High-speed suspend and resume
Figure 17 illustrates how a host or a hub places a high-speed enabled peripheral into suspend and then initiates resume signaling. The high-speed peripheral will wake up and return to high-speed operations. Note that Figure 17 timing is not to scale, and does not show all RXCMD LINESTATE updates.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
36 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
The sequence of events related to a host and a peripheral, both with ISP1506, is as follows. 1. High-speed idle: Initially, the host and the peripheral are idle. The host has its 15 k pull-down resistors enabled (DP_PULLDOWN and DM_PULLDOWN are set to 1b) and 45 terminations enabled (TERMSELECT is set to 0b). The peripheral has its 45 terminations enabled (TERMSELECT is set to 0b). 2. Full-speed suspend: When the peripheral sees no bus activity for 3 ms, it enters the suspend state. The peripheral link places the ISP1506 into full-speed mode (XCVRSELECT is set to 01b), removes 45 terminations, and enables the 1.5 k pull-up resistor on DP (TERMSELECT is set to 1b). The peripheral link then places the ISP1506 into low-power mode by clearing SUSPENDM, causing the ISP1506 to draw only suspend current. The host also changes the ISP1506 to full-speed (XCVRSELECT is set to 01b), removes 45 terminations (TERMSELECT is set to 1b), and then may or may not be powered down. 3. Resume K: When the host wants to wake up the peripheral, it sets OPMODE to 10b and transmits a full-speed K for at least 20 ms. The peripheral link sees the resume K (10b) on LINESTATE, and asserts STP to wake up the ISP1506. 4. High-speed traffic: The host link sets high-speed (XCVRSELECT is set to 00b) and enables its 45 terminations (TERMSELECT is set to 0b). The peripheral link sees SE0 on LINESTATE and also sets high-speed (XCVRSELECT is set to 00b) and enables its 45 terminations (TERMSELECT is set to 0b). The host link sets OPMODE to 00b for normal high-speed operation.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
37 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
HS idle TXCMD (REGW) DATA [ 3:0] ULPI HS host (DP_PULLDOWN = 1b, DM_PULLDOWN = 1b) DIR STP
FS suspend TXCMD TXCMD (REGW) NOPID
resume K TXCMD ... K (REGW)
HS idle
K
K
NXT
XCVR SELECT TERM SELECT OP MODE
00b
01b
00b
00b !squelch squelch (01b) (00b) FS J (01b)
10b FS K (10b)
00b squelch (00b) !squelch (01b)
LINE STATE
CLOCK TXCMD (REGW) ULPI HS peripheral (DP_PULLDOWN = 0b) DATA [ 3:0] DIR LINESTATE J LINESTATE K SE0 TXCMD (REGW)
STP NXT XCVR SELECT TERM SELECT OPMODE 00b 10b 00b
00b
01b
00b
SUSPENDM LINE STATE !squelch squelch (01b) (00b) FS J (01b) FS K (10b) squelch (00b) !squelch (01b)
USB signals
DP
DM
004aaa766
Timing is not to scale.
Fig 17. High-speed suspend and resume
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
38 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
9.10.3 Remote wake-up
The ISP1506 supports peripherals that initiate remote wake-up resume. When placed into USB suspend, the peripheral link remembers at what speed it was originally operating. Depending on the original speed, the link follows one of the protocols detailed here. In Figure 18, timing is not to scale, and not all RXCMD LINESTATE updates are shown. The sequence of events related to a host and a peripheral, both with ISP1506, is as follows. 1. Both the host and the peripheral are assumed to be in low-power mode. 2. The peripheral begins remote wake-up by re-enabling its clock and setting its SUSPENDM bit to 1b. 3. The peripheral begins driving K on the bus to signal resume. Note that the peripheral link must assume that LINESTATE is K (01b) while transmitting because it will not receive any RXCMDs. 4. The host recognizes the resume, re-enables its clock and sets its SUSPENDM bit. 5. The host takes over resume driving within 1 ms of detecting the remote wake-up. 6. The peripheral stops driving resume. 7. The peripheral sees the host continuing to drive the resume. 8. The host stops driving resume and the ISP1506 automatically adds the EOP to the end of the resume. The peripheral recognizes the EOP as the end of resume. 9. Both the host and the peripheral revert to normal operation by writing 00b to OPMODE. If the host or the peripheral was previously in high-speed mode, it must revert to high-speed before the SE0 of the EOP is completed. This can be achieved by writing XCVRSELECT[1:0] = 00b and TERMSELECT = 0b after LINESTATE indicates SE0.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
39 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
LINESTATE DATA [ 3:0] DIR STP
TXCMD REGW
TXCMD NOPID
00h
TXCMD REGW
ULPI host
NXT
XCVR SELECT TERM SELECT OP MODE
01b (FS), 10b (LS)
00b (HS only)
0b (HS only)
10b
00b
LINESTATE DATA [ 3:0] DIR
TXCMD REGW
TXCMD NOPID
00h
RXCMD
RXCMD
RXCMD TXCMD REGW
ULPI peripheral
STP
NXT
XCVR SELECT
00b (HS), 01b (FS), 10b (LS)
00b (HS only)
TERM SELECT OP MODE 10b
0b (HS only)
00b
004aaa767
Timing is not to scale.
Fig 18. Remote wake-up from low-power mode
9.11 No automatic SYNC and EOP generation (optional)
This setting allows the link to turn off the automatic SYNC and EOP generation, and must be used for high-speed packets only. It is provided for backward compatibility with legacy controllers that include SYNC and EOP bytes in the data payload when transmitting packets. The ISP1506 will not automatically generate SYNC and EOP patterns when OPMODE[1:0] is set to 11b. The ISP1506 will still NRZI encode data and perform bit stuffing. An example of a sequence is shown in Figure 19. The link must always send packets using the TXCMD (NOPID) type. The ISP1506 does not provide a mechanism to control bit stuffing in individual bytes, but will automatically turn off bit stuffing for EOP when STP is asserted with data set to FEh. If data is set to 00h when STP is asserted, the
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
40 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
PHY will not transmit any EOP. The ISP1506 will also detect if the PID byte is A5h, indicating an SOF packet, and automatically send a long EOP when STP is asserted. To transmit chirp and resume signaling, the link must set OPMODE to 10b.
CLOCK ... ... D N - 1 DN
TXCMD ULPI signals DATA [3:0] DIR STP NXT
00h
00h 00h 80h PID
D1
D2
D3
FEh
UTMI+ equivalent signals USB bus
TXVALID TXREADY TXBIT STUFF ENABLE IDLE DP, DM
004aaa893
SYNC
PID
DATA PAYLOAD
EOP
IDLE
Fig 19. Transmitting USB packets without the automatic SYNC and EOP generation
9.12 On-The-Go operations
On-The-Go (OTG) is a supplement to Ref. 1 "Universal Serial Bus Specification Rev. 2.0" that allows a portable USB device to assume the role of a limited USB host by defining improvements, such as a small connector and low power. Non-portable devices, such as standard hosts and embedded hosts, can also benefit from OTG features. The ISP1506 OTG PHY is designed to support all the tasks specified in the OTG supplement. The ISP1506 provides the front-end analog support for Host Negotiation Protocol (HNP) and Session Request Protocol (SRP) for dual-role devices. The supporting components include:
* Built-in 5 V charge pump * Voltage comparators
- A_VBUS_VLD - SESS_VLD (session valid, can be used for both A-session and B-session valid) - SESS_END (session end)
* Pull-up and pull-down resistors on DP and DM * ID detector indicates if micro-A or micro-B plug is inserted * Charge and discharge resistors on VBUS
The following subsections describe how to use the ISP1506 OTG components.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
41 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
9.12.1 OTG charge pump
A description of the charge pump is given in Section 7.6.4. When the controller is configured as an A-device, it can provide the VBUS power by turning on the charge pump. Control of the charge pump is described in Section 9.4.1 and Section 10.1.4.
9.12.2 OTG comparators
The ISP1506 provides comparators that conform to Ref. 2 "On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3" requirements of VA_VBUS_VLD, VA_SESS_VLD, VB_SESS_VLD and VB_SESS_END. In this data sheet, VA_SESS_VLD and VB_SESS_VLD are combined into VB_SESS_VLD. Comparators are described in Section 7.6.2. Changes in comparator values are communicated to the link by RXCMDs as described in Section 9.5.2.2. Control over comparators is described in Section 10.1.5 to Section 10.1.8.
9.12.3 Pull-up and pull-down resistors
The USB resistors on DP and DM can be used to initiate data-line pulsing SRP. The link must set the required bus state using mode settings in Table 7.
9.12.4 ID detection
The ISP1506 provides an internal pull-up resistor to sense the value of the ID pin. The pull-up resistor must first be enabled by setting the ID_PULLUP register bit to logic 1. If the value on ID has changed, the ISP1506 will send an RXCMD or interrupt to the link by time tID. If the link does not receive any RXCMD or interrupt by tID, then the ID value has not changed.
9.12.5 VBUS charge and discharge resistors
A pull-up resistor, RUP(VBUS), is provided to perform VBUS pulsing SRP. A B-device is allowed to charge VBUS above the session valid threshold to request the host to turn on the VBUS power. A pull-down resistor, RDN(VBUS), is provided for a B-device to discharge VBUS. This is done whenever the A-device turns off the VBUS power. The B-device can use the pull-down resistor to ensure VBUS is below VB_SESS_END before starting a session. For details, refer to Ref. 2 "On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3".
9.13 Serial mode
The ISP1506 supports 3-pin serial mode, controlled by bit 3PIN_FSLS_SERIAL of the Interface Control register. For details, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1", Section 3.10. Figure 20 provides an example of 3-pin serial mode.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
42 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
TRANSMIT SYNC DATA0 (TX_ENABLE) DATA EOP SYNC
RECEIVE DATA EOP
DATA1 (DAT) DATA2 (SE0)
DP
DM
004aaa982
Fig 20. Example of transmit followed by receive in 3-pin serial mode
9.14 Aborting transfers
The ISP1506 supports aborting transfers on the ULPI bus. For details, refer to Ref. 3 "UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1", Section 3.8.4.
9.15 Avoiding contention on the ULPI data bus
Because the ULPI data bus is bidirectional, avoid situations in which both the link and the PHY simultaneously drive the data bus. The following points must be considered while implementing the data bus drive control on the link. After power-up and clock stabilization, default states are as follows:
* The ISP1506 drives DIR to LOW. * The data bus is input to the ISP1506. * The ULPI link data bus is output, with all data bus lines driven to LOW.
When the ISP1506 wants to take control of the data bus to initiate a data transfer, it changes the DIR value from LOW to HIGH. At this point, the link must disable its output buffers. This must be as fast as possible so the link must use a combinational path from DIR. The ISP1506 will not immediately enable its output buffers, but will delay the enabling of its buffers until the next clock edge, avoiding bus contention. When the data transfer is no longer required by the ISP1506, it changes DIR from HIGH to LOW and starts to immediately turn off its output drivers. The link senses the change of DIR from HIGH to LOW, but delays enabling its output buffers for one CLOCK cycle, avoiding data bus contention.
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
43 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
10. Register map
Table 18. Immediate register set overview Size (bit) 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 2Fh Address (6 bit) R[1] 00h 01h 02h 03h 04h to 06h 07h to 09h W[2] 04h 07h S[3] 05h 08h 0Bh 0Eh 11h 17h 19h to 2Eh 30h to 3Ch 3Dh to 3Fh C[4] 06h 09h 0Ch 0Fh 12h 18h Section 10.1.2 on page 45 Section 10.1.3 on page 46 Section 10.1.4 on page 47 Section 10.1.5 on page 48 Section 10.1.6 on page 49 Section 10.1.7 on page 49 Section 10.1.8 on page 50 Section 10.1.9 on page 51 Section 10.1.10 on page 51 Section 10.1.11 on page 51 Section 10.1.12 on page 51 Section 10.1.13 on page 51 Section 10.1.14 on page 51 Section 10.1.1 on page 45 References Field name Vendor ID Low register Vendor ID High register Product ID Low register Product ID High register Function Control register Interface Control register OTG Control register USB Interrupt Enable Rising Edge register USB Interrupt Enable Falling Edge register USB Interrupt Status register USB Interrupt Latch register Debug register Scratch register Reserved (do not use) Access extended register set Vendor-specific register Power Control register
[1] [2] [3] [4]
0Ah to 0Ch 0Ah 0Dh to 0Fh 0Dh 10h to 12h 13h 14h 15h 16h to 18h 10h 16h
Read (R): A register can be read. Read-only if this is the only mode given. Write (W): The pattern on the data bus will be written over all bits of a register. Set (S): The pattern on the data bus is OR-ed with and written to a register. Clear (C): The pattern on the data bus is a mask. If a bit in the mask is set, then the corresponding register bit will be set to zero (cleared).
Table 19.
Extended register set overview Size (bit) 8 8 Address (6 bit) R[1] W[2] S[3] C[4] Section 10.2 on page 52 00h to 3Fh 40h to FFh References
Field name Maps to immediate register set above Reserved (do not use)
[1] [2] [3] [4]
Read (R): A register can be read. Read-only if this is the only mode given. Write (W): The pattern on the data bus will be written over all bits of a register. Set (S): The pattern on the data bus is OR-ed with and written to a register. Clear (C): The pattern on the data bus is a mask. If a bit in the mask is set, then the corresponding register bit will be set to zero (cleared).
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
44 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
10.1 Immediate register set
10.1.1 Vendor ID and Product ID registers
10.1.1.1 Vendor ID Low register Table 20 shows the bit description of the register.
Table 20. Bit 7 to 0 Vendor ID Low register (address R = 00h) bit description Symbol VENDOR_ID_ LOW[7:0] Access R Value CCh Description Vendor ID Low: Lower byte of the NXP vendor ID supplied by USB-IF; has a fixed value of CCh
10.1.1.2
Vendor ID High register The bit description of the register is given in Table 21.
Table 21. Bit 7 to 0
Vendor ID High register (address R = 01h) bit description Symbol VENDOR_ID_ HIGH[7:0] Access R Value 04h Description Vendor ID High: Upper byte of the NXP vendor ID supplied by USB-IF; has a fixed value of 04h
10.1.1.3
Product ID Low register The bit description of the Product ID Low register is given in Table 22.
Table 22. Bit 7 to 0
Product ID Low register (address R = 02h) bit description Symbol PRODUCT_ID_ LOW[7:0] Access R Value 06h Description Product ID Low: Lower byte of the NXP product ID number; has a fixed value of 06h
10.1.1.4
Product ID High register The bit description of the register is given in Table 23.
Table 23. Bit 7 to 0
Product ID High register (address R = 03h) bit description Access R Value 15h Description Product ID High: Upper byte of the NXP product ID number; has a fixed value of 15h
Symbol PRODUCT_ID_ HIGH[7:0]
10.1.2 Function Control register
This register controls UTMI function settings of the PHY. The bit allocation of the register is given in Table 24.
Table 24. Bit Symbol Reset Access Function Control register (address R = 04h to 06h, W = 04h, S = 05h, C = 06h) bit allocation 7 reserved 0 R/W/S/C 6 SUSPENDM 1 R/W/S/C 5 RESET 0 R/W/S/C 4 3 2 TERM SELECT 0 R/W/S/C 1 0 OPMODE[1:0] 0 R/W/S/C 0 R/W/S/C XCVRSELECT[1:0] 0 R/W/S/C 1 R/W/S/C
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
45 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 25. Bit 7 6 -
Function Control register (address R = 04h to 06h, W = 04h, S = 05h, C = 06h) bit description Description reserved Suspend LOW: Active LOW PHY suspend. Places the PHY into low-power mode. The PHY will power down all blocks, except the full-speed receiver, OTG comparators and ULPI interface pins. To come out of low-power mode, the link must assert STP. The PHY will automatically clear this bit when it exits low-power mode. 0b -- Low-power mode 1b -- Powered (default)
Symbol SUSPENDM
5
RESET
Reset: Active HIGH transceiver reset. After the link sets this bit, the PHY will assert DIR and reset the digital core. This does not reset the ULPI interface or the ULPI register set. When reset is completed, the PHY will deassert DIR and automatically clear this bit, followed by an RXCMD update to the link. 0b -- Do not reset (default) 1b -- Reset The link must wait for DIR to deassert before using the ULPI bus. Does not reset the ULPI interface or ULPI register set.
4 to 3
OPMODE [1:0]
Operation Mode: Selects the required bit-encoding style during transmit. 00b -- Normal operation (default) 01b -- Non-driving 10b -- Disable bit-stuffing and NRZI encoding 11b -- Do not automatically add SYNC and EOP when transmitting; must be used only for high-speed packets
2
TERMSELECT
Termination Select: Controls the internal 1.5 k full-speed pull-up resistor and 45 high-speed terminations. Control over bus resistors changes, depending on XCVRSELECT[1:0], OPMODE[1:0], DP_PULLDOWN and DM_PULLDOWN, as shown in Table 7. Transceiver Select: Selects the required transceiver speed. 00b -- Enable the high-speed transceiver 01b -- Enable the full-speed transceiver (default) 10b -- Enable the low-speed transceiver 11b -- Enable the full-speed transceiver for low-speed packets (full-speed preamble is automatically prefixed)
1 to 0
XCVRSELECT [1:0]
10.1.3 Interface Control register
The Interface Control register enables alternative interfaces. All of these modes are optional features provided for legacy link cores. Setting more than one of these fields results in undefined behavior. Table 26 provides the bit allocation of the register.
Table 26. Bit Symbol Reset Access Interface Control register (address R = 07h to 09h, W = 07h, S = 08h, C = 09h) bit allocation 7 INTF_ PROT_DIS 0 R/W/S/C 6 IND_PASS THRU 0 R/W/S/C 5 IND_ COMPL 0 R/W/S/C 4 reserved 0 R/W/S/C 3 CLOCK_ SUSPENDM 0 R/W/S/C 2 reserved 0 R/W/S/C 1 3PIN_FSLS _SERIAL 0 R/W/S/C 0 reserved 0 R/W/S/C
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
46 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 27. Bit 7
Interface Control register (address R = 07h to 09h, W = 07h, S = 08h, C = 09h) bit description Description Interface Protect Disable: Controls circuitry built into the ISP1506 to protect the ULPI interface when the link 3-states STP and DATA[3:0]. When this bit is enabled, the ISP1506 will automatically detect when the link stops driving STP. 0b -- Enables the interface protect circuit (default). The ISP1506 attaches a weak pull-up resistor on STP. If STP is unexpectedly HIGH, the ISP1506 attaches weak pull-down resistors on DATA[3:0], protecting data inputs. 1b -- Disables the interface protect circuit, detaches weak pull-down resistors on DATA[3:0], and a weak pull-up resistor on STP.
Symbol INTF_PROT_DIS
6
IND_PASSTHRU
Indicator Pass-through: The ISP1506 does not support the qualification of an external FAULT with the internal VA_VBUS_VLD comparator. Either a digital FAULT is input on the VBUS/FAULT pin or the VBUS power is connected to the VBUS/FAULT pin, not both. This bit must always be set to logic 1. 0b -- Not supported. 1b -- The complement output signal is not qualified with the internal A_VBUS_VLD comparator. The link must always set this bit to logic 1.
5
IND_COMPL
Indicator Complement: Informs the PHY to invert the FAULT input signal, generating the complement output. For details, see Section 9.5.2.2. 0b -- The ISP1506 will not invert the FAULT signal (default). 1b -- The ISP1506 will invert the FAULT signal.
4 3
CLOCK_ SUSPENDM
reserved Clock Suspend LOW: Active LOW clock suspend. Powers down the internal clock circuitry only. By default, the clock will not be powered in 3-pin serial mode. Valid only in 3-pin serial mode. Valid only when SUSPENDM is set to logic 1, otherwise this bit is ignored. 0b -- Clock will not be powered in 3-pin serial mode (default). 1b -- Clock will be powered in 3-pin serial mode.
2 1
3PIN_FSLS_ SERIAL
reserved 3-Pin Full-Speed Low-Speed Serial Mode: Changes the ULPI interface to a 3-bit serial interface. The PHY will automatically clear this bit when 3-pin serial mode is exited. 0b -- Full-speed or low-speed packets are sent using the parallel interface (default). 1b -- Full-speed or low-speed packets are sent using the 3-pin serial interface.
0
-
reserved
10.1.4 OTG Control register
This register controls various OTG functions of the ISP1506. The bit allocation of the OTG Control register is given in Table 28.
Table 28. Bit Symbol Reset Access OTG Control register (address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh, C = 0Ch) bit allocation 7 6 5 DRV_ VBUS 0 R/W/S/C 4 CHRG_ VBUS 0 R/W/S/C 3 DISCHRG_ VBUS 0 R/W/S/C 2 DM_PULL DOWN 1 R/W/S/C 1 DP_PULL DOWN 1 R/W/S/C 0 ID_PULL UP 0 R/W/S/C USE_EXT_ DRV_ VBUS_IND VBUS_EXT 0 R/W/S/C 0 R/W/S/C
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
47 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 29. Bit 7
OTG Control register (address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh, C = 0Ch) bit description Description Use External VBUS Indicator: Informs the PHY to use an external VBUS overcurrent indicator. 0b -- Use the internal OTG comparator (default). 1b -- Use the external VBUS valid indicator signal input from the FAULT pin. Drive VBUS External: Selects between the internal and external 5 V VBUS supply. Using an external charge pump or a 5 V supply is optional. 0b -- Drives VBUS using the internal charge pump. Also ensures PSW_N is not driven to LOW (default). 1b -- Drives VBUS using the external charge pump or the 5 V supply. Drives PSW_N to LOW.
Symbol USE_EXT_ VBUS_IND
6
DRV_VBUS_ EXT
5
DRV_VBUS
Drive VBUS: Signals the ISP1506 to drive 5 V on VBUS. If DRV_VBUS_EXT is set to logic 1, then setting DRV_VBUS is optional. 0b -- Do not drive VBUS (default). 1b -- Drive 5 V on VBUS.
4
CHRG_VBUS
Charge VBUS: Charges VBUS through a resistor. Used for the VBUS pulsing SRP. The link must first check that VBUS is discharged (see bit DISCHRG_VBUS), and that both the DP and DM data lines have been LOW (SE0) for 2 ms. 0b -- Do not charge VBUS (default). 1b -- Charge VBUS.
3
DISCHRG_ VBUS
Discharge VBUS: Discharges VBUS through a resistor. If the link sets this bit to logic 1, it waits for an RXCMD indicating that SESS_END has changed from 0 to 1, and then resets this bit to 0 to stop the discharge. 0b -- Do not discharge VBUS (default). 1b -- Discharge VBUS.
2
DM_PULL DOWN
DM Pull Down: Enables the 15 k pull-down resistor on DM. 0b -- Pull-down resistor is not connected to DM. 1b -- Pull-down resistor is connected to DM (default). DP Pull Down: Enables the 15 k pull-down resistor on DP. 0b -- Pull-down resistor is not connected to DP. 1b -- Pull-down resistor is connected to DP (default). ID Pull Up: Connects a pull-up to the ID line and enables sampling of the ID level. Disabling the ID line sampler will reduce the PHY power consumption. 0b -- Disables sampling of the ID line (default). 1b -- Enables sampling of the ID line.
1
DP_PULL DOWN
0
ID_PULLUP
10.1.5 USB Interrupt Enable Rising Edge register
The bits in this register enable interrupts and RXCMDs to be sent when the corresponding bits in the USB Interrupt Status register change from logic 0 to logic 1. By default, all transitions are enabled. Table 30 shows the bit allocation of the register.
Table 30. Bit Symbol Reset Access
ISP1506A_ISP1506B_2
USB Interrupt Enable Rising Edge register (address R = 0Dh to 0Fh, W = 0Dh, S = 0Eh, C = 0Fh) bit allocation 7 6 reserved 0 R/W/S/C 0 R/W/S/C 0 R/W/S/C 5 4 ID_GND_R 1 R/W/S/C 3 SESS_ END_R 1 R/W/S/C 2 SESS_ VALID_R 1 R/W/S/C 1 VBUS_ VALID_R 1 R/W/S/C 0 HOST_ DISCON_R 1 R/W/S/C
48 of 79
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 31. Bit 7 to 5 4 3 2 1 0
USB Interrupt Enable Rising Edge register (address R = 0Dh to 0Fh, W = 0Dh, S = 0Eh, C = 0Fh) bit description Description reserved ID Ground Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on ID_GND. Session End Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on SESS_END. Session Valid Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on SESS_VLD. VBUS Valid Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on VBUS_VLD. Host Disconnect Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on HOST_DISCON.
Symbol ID_GND_R SESS_END_R SESS_VALID_R VBUS_VALID_R HOST_DISCON_ R
10.1.6 USB Interrupt Enable Falling Edge register
The bits in this register enable interrupts and RXCMDs to be sent when the corresponding bits in the USB Interrupt Status register change from logic 1 to logic 0. By default, all transitions are enabled. See Table 32.
Table 32. Bit Symbol Reset Access Table 33. Bit 7 to 5 4 3 2 1 0 0 R/W/S/C USB Interrupt Enable Falling Edge register (address R = 10h to 12h, W = 10h, S = 11h, C = 12h) bit allocation 7 6 reserved 0 R/W/S/C 0 R/W/S/C 5 4 ID_GND_F 1 R/W/S/C 3 SESS_ END_F 1 R/W/S/C 2 SESS_ VALID_F 1 R/W/S/C 1 VBUS_ VALID_F 1 R/W/S/C 0 HOST_ DISCON_F 1 R/W/S/C
USB Interrupt Enable Falling Edge register (address R = 10h to 12h, W = 10h, S = 11h, C = 12h) bit description Symbol ID_GND_F SESS_END_F SESS_VALID_F VBUS_VALID_F Description reserved ID Ground Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on ID_GND. Session End Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on SESS_END. Session Valid Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on SESS_VLD. VBUS Valid Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on VBUS_VLD.
HOST_DISCON_ Host Disconnect Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on F HOST_DISCON.
10.1.7 USB Interrupt Status register
This register (see Table 34) indicates the current value of the interrupt source signal.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
49 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 34. Bit Symbol Reset Access Table 35. Bit 7 to 5 4 3 2 1 0 -
USB Interrupt Status register (address R = 13h) bit allocation 7 6 reserved X R X R X R 5 4 ID_GND 0 R 3 SESS_ END 0 R 2 SESS_ VALID 0 R 1 VBUS_ VALID 0 R 0 HOST_ DISCON 0 R
USB Interrupt Status register (address R = 13h) bit description Symbol ID_GND SESS_END SESS_VALID VBUS_VALID HOST_DISCON Description reserved ID Ground: Reflects the current value of the ID detector circuit. Session End: Reflects the current value of the session end voltage comparator. Session Valid: Reflects the current value of the session valid voltage comparator. VBUS Valid: Reflects the current value of the VBUS valid voltage comparator. Host Disconnect: Reflects the current value of the host disconnect detector.
10.1.8 USB Interrupt Latch register
The bits of the USB Interrupt Latch register are automatically set by the ISP1506 when an unmasked change occurs on the corresponding interrupt source signal. The ISP1506 will automatically clear all bits when the link reads this register, or when the PHY enters low-power mode. Remark: It is optional for the link to read this register when the clock is running because all signal information will automatically be sent to the link through the RXCMD byte. The bit allocation of this register is given in Table 36.
Table 36. Bit Symbol Reset Access Table 37. Bit 7 to 5 4 3 2 1 0 0 R USB Interrupt Latch register (address R = 14h) bit allocation 7 6 reserved 0 R 0 R 5 4 ID_GND_L 0 R 3 SESS_ END_L 0 R 2 SESS_ VALID_L 0 R 1 VBUS_ VALID_L 0 R 0 HOST_ DISCON_L 0 R
USB Interrupt Latch register (address R = 14h) bit description Description ID Ground Latch: Automatically set when an unmasked event occurs on ID_GND. Cleared when this register is read. Session End Latch: Automatically set when an unmasked event occurs on SESS_END. Cleared when this register is read. Session Valid Latch: Automatically set when an unmasked event occurs on SESS_VLD. Cleared when this register is read. VBUS Valid Latch: Automatically set when an unmasked event occurs on VBUS_VLD. Cleared when this register is read. Host Disconnect Latch: Automatically set when an unmasked event occurs on HOST_DISCON. Cleared when this register is read.
Symbol reserved ID_GND_L SESS_END_L SESS_VALID_L VBUS_VALID_L HOST_DISCON_L
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
50 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
10.1.9 Debug register
The bit allocation of the Debug register is given in Table 38. This register indicates the current value of signals useful for debugging.
Table 38. Bit Symbol Reset Access Table 39. Bit 7 to 2 1 0 0 R 0 R 0 R Debug register (address R = 15h) bit allocation 7 6 5 reserved 0 R 0 R 0 R 4 3 2 1 LINE STATE1 0 R 0 LINE STATE0 0 R
Debug register (address R = 15h) bit description Symbol LINESTATE1 LINESTATE0 Description reserved Line State 1: Contains the current value of LINESTATE 1 Line State 0: Contains the current value of LINESTATE 0
10.1.10 Scratch register
Table 40 shows the bit description of the Scratch register. It is an empty register for testing purposes.
Table 40. Bit 7 to 0 Scratch register (address R = 16h to 18h, W = 16h, S = 17h, C = 18h) bit description Symbol SCRATCH[7:0] Access R/W/S/C Value 00h Description Scratch: This is an empty register byte for testing purposes. Software can read, write, set and clear this register, and the functionality of the PHY will not be affected.
10.1.11 Reserved
Registers 19h to 2Eh are not implemented. Operating on these addresses will have no effect on the PHY.
10.1.12 Access extended register set
Address 2Fh does not contain register data. Instead it links to the extended register set. The immediate register set maps to the lower end of the extended register set.
10.1.13 Vendor-specific registers
Addresses 30h to 3Fh contain vendor-specific registers.
10.1.14 Power Control register
This register controls various aspects of the ISP1506. Table 41 shows the bit allocation of the register.
Table 41. Bit Symbol Reset Access
ISP1506A_ISP1506B_2
Power Control register (address R = 3Dh to 3Fh, W = 3Dh, S = 3Eh, C = 3Fh) bit allocation 7 6 reserved 0 R/W/S/C 0 R/W/S/C 0 R/W/S/C 0 R/W/S/C 5 4 3 BVALID_ FALL 0 R/W/S/C 2 BVALID_ RISE 0 R/W/S/C 1 reserved 0 R/W/S/C 0 IGNORE_ RESET 0 R/W/S/C
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
51 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 42. Bit 3 7 to 4 -
Power Control register (address R = 3Dh to 3Fh, W = 3Dh, S = 3Eh, C = 3Fh) bit description Description reserved; the link must never write logic 1 to these bits BVALID Fall: Enables RXCMDs for HIGH-to-LOW transitions on BVALID. When BVALID changes from HIGH to LOW, the ISP1506 will send an RXCMD to the link with the ALT_INT bit set to logic 1. This bit is optional and is not necessary for OTG devices. This bit is provided for debugging purposes. The session valid comparator should be used instead.
Symbol BVALID_FALL
2
BVALID_RISE
BVALID Rise: Enables RXCMDs for LOW-to-HIGH transitions on BVALID. When BVALID changes from LOW to HIGH, the ISP1506 will send an RXCMD to the link with the ALT_INT bit set to logic 1. This bit is optional and is not necessary for OTG devices. This bit is provided for debugging purposes. The session valid comparator should be used instead.
1 0
reserved IGNORE_RESET
Ignore Reset: Selects between the RESET_N and PSW_N functions of the RESET_N/PSW_N pin. The link must set this bit to logic 1 if PSW_N is used in a ganged mode configuration. 0b -- The RESET_N/PSW_N pin behaves as an active-LOW reset input (RESET_N) (default). 1b -- The RESET_N/PSW_N pin behaves as an active-LOW power switch output (PSW_N).
10.2 Extended register set
Addresses 00h to 3Fh of the extended register set directly map to the immediate set. This means a read, write, set or clear operation to these extended addresses will operate on the immediate register set. Addresses 40h to FFh are not implemented. Operating on these addresses may result in undefined behavior of the PHY.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
52 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
11. ElectroStatic Discharge (ESD)
11.1 ESD protection
The pins that are connected to the USB connector (DP, DM, ID, VBUS and GND) have a minimum of 4 kV ESD protection. Capacitors 0.1 F and 1 F must be connected in parallel from VBUS to GND to achieve this 4 kV ESD protection (see Figure 21). Remark: Capacitors 0.1 F and 1 F are also required by Ref. 1 "Universal Serial Bus Specification Rev. 2.0". For details on the requirements for CVBUS, see Section 16.
RC 1 M RD 1500
charge current limit resistor
discharge resistance A
DEVICE UNDER TEST VBUS
HIGH VOLTAGE DC SOURCE
CS 100 pF
storage capacitor
B
0.1 F
1 F
GND
004aaa881
Fig 21. Human body ESD test model
11.2 ESD test conditions
A detailed report on test set up and results is available on request.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
53 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
12. Limiting values
Table 43. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol VCC VCC(I/O) VI Parameter supply voltage input/output supply voltage input voltage on pins STP, DATA[3:0] and RESET_N/PSW_N on pin VBUS/FAULT on pin XTAL1 on pin ID on pins DP and DM VESD Ilu Tstg
[1]
[1] [2] [2]
Conditions
Min -0.5 -0.5 -0.5 -0.5 -0.5 -0.5 -0.5 -4 -1.5 -40
Max +4.6 +2.5
Unit V V
VCC(I/O) + 0.5 V +6.0 +2.5 +4.6 +4.6 +4 +1.5 100 +125 V V V V kV kV mA C
electrostatic discharge voltage latch-up current storage temperature
pins DP, DM, ID, VBUS and GND; ILI < 1 A all other pins; ILI < 1 A -0.5 x VCC < V < +1.5 x VCC
The ISP1506 has been tested according to the additional requirements listed in Ref. 1 "Universal Serial Bus Specification Rev. 2.0", Section 7.1.1. The short circuit withstand test and the AC stress test were performed for 24 hours, and the ISP1506 was found to be fully operational after the test completed. Equivalent to discharging a 100 pF capacitor through a 1.5 k resistor (Human Body Model JESD22-A114D).
[2]
13. Recommended operating conditions
Table 44. Symbol VCC VCC(I/O) VI Recommended operating conditions Parameter supply voltage input/output supply voltage input voltage on pins STP, DATA[3:0] and RESET_N/PSW_N on pin VBUS/FAULT on pins DP, DM and ID on pin XTAL1 Tamb Tj ambient temperature junction temperature Conditions Min 3.0 1.65 0 0 0 0 -40 -40 Typ 3.3 +25 Max 3.6 1.95 VCC(I/O) 5.5 3.6 1.95 +85 +125 Unit V V V V V V C C
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
54 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
14. Static characteristics
Table 45. Static characteristics: supply pins VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Typical values are at VCC = 3.3 V; VCC(I/O) = 1.8 V; Tamb = +25 C; unless otherwise specified. Symbol Parameter Conditions Min 3.0 1.65 1.0 charge pump disabled low-power mode; VBUS valid detector disabled; 1.5 k pull-up resistor on pin DP disconnected low-power mode; VBUS valid detector disabled; 1.5 k pull-up resistor on pin DP connected full-speed idle; no USB activity high-speed idle; no USB activity full-speed continuous data transmit; 50 pF load on pins DP and DM full-speed continuous data receive high-speed continuous data transmit; 45 load on pins DP and DM to ground high-speed continuous data receive charge pump enabled IO(VBUS) = 8 mA; charge pump supply current only IO(VBUS) = 0 mA; charge pump supply current only ICC(I/O) supply current on pin VCC(I/O) ULPI interface pins are static 20 300 23 1 mA A A
[1]
Typ 3.3 1.8 30
Max 3.6 1.95 1.5 85
Unit V V V A
V(REG3V3) voltage on pin REG3V3 V(REG1V8) voltage on pin REG1V8 VPOR(trip) ICC power-on reset trip voltage supply current
-
-
210
280
A
-
10 19 15 11 48
-
mA mA mA mA mA
[1] [1]
[1]
-
28
-
mA
[1]
A continuous stream of 1 kB packets with minimum inter-packet gap and all data bits set to logic 0 for continuous toggling.
Table 46. Static characteristics: digital pins (CLOCK, DIR, STP, NXT, DATA[3:0], RESET_N/PSW_N) VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Typical values are at VCC = 3.3 V; VCC(I/O) = 1.8 V; Tamb = +25 C; unless otherwise specified. Symbol VIL VIH IIL IIH ILI VOL Parameter LOW-level input voltage HIGH-level input voltage LOW-level input current HIGH-level input current input leakage current LOW-level output voltage IOL = +2 mA VI = 0 V VI = VCC(I/O) Conditions Min -1 Typ +0.1 Max Unit Input levels 0.25 x VCC(I/O) V 1 1 +1 0.4 V A A A V
(c) NXP B.V. 2008. All rights reserved.
0.8 x VCC(I/O) -
Output levels
ISP1506A_ISP1506B_2
Product data sheet
Rev. 02 -- 28 August 2008
55 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 46. Static characteristics: digital pins (CLOCK, DIR, STP, NXT, DATA[3:0], RESET_N/PSW_N) ...continued VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Typical values are at VCC = 3.3 V; VCC(I/O) = 1.8 V; Tamb = +25 C; unless otherwise specified. Symbol VOH IOH IOL IOZ ZL Ipd Parameter Conditions Min -3.8 2.8 40 interface protect enabled; DATA[3:0] pins only; VI = VCC(I/O) interface protect enabled; STP pin only; VI = 0 V pins STP, RESET_N, CLOCK, DATA[3:0] 25 Typ 50 Max 1 75 90 Unit V mA mA A A HIGH-level output voltage IOH = -2 mA HIGH-level output current VO = VCC(I/O) - 0.4 V LOW-level output current off-state output current load impedance pull-down current VO = 0.4 V 0 V < VO < VCC(I/O) VCC(I/O) - 0.4 -
Impedance Pull-up and pull-down
Ipu
pull-up current
-30
-50
-75
A
Capacitance Cin input capacitance 3.5 pF
Table 47. Static characteristics: digital pin FAULT VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Symbol VIL VIH IIL IIH Parameter LOW-level input voltage HIGH-level input voltage LOW-level input current HIGH-level input current VI = 0 V VI = VCC(I/O) Conditions Min 2.0 Typ Max 0.8 1 1 Unit V V A A Input levels
Table 48. Static characteristics: analog I/O pins (DP, DM) VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Typical values are at VCC = 3.3 V; VCC(I/O) = 1.8 V; Tamb = +25 C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Original USB transceiver (low-speed and full-speed) Input levels (differential receiver) VDI VCM differential input sensitivity voltage |VDP - VDM| differential common mode voltage range LOW-level input voltage HIGH-level input voltage LOW-level output voltage HIGH-level output voltage pull-up on pin DP; RL = 1.5 k to 3.6 V pull-down on pins DP and DM; RL = 15 k to GND includes VDI range 0.2 0.8 2.5 V V
Input levels (single-ended receivers) VIL VIH VOL VOH 2.0 0.0 2.8 0.18 3.2 0.8 0.3 3.6 V V V V
Output levels
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
56 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 48. Static characteristics: analog I/O pins (DP, DM) ...continued VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Typical values are at VCC = 3.3 V; VCC(I/O) = 1.8 V; Tamb = +25 C; unless otherwise specified. Symbol Termination VTERM Resistance RUP(DP) pull-up resistance on pin DP 1425 1500 1575 High-speed USB transceiver Input levels (differential receiver) VHSSQ high-speed squelch detection threshold voltage (differential signal amplitude) high-speed disconnect detection threshold voltage (differential signal amplitude) high-speed differential input sensitivity high-speed data signaling common mode voltage range (guideline for receiver) high-speed idle level voltage high-speed data signaling LOW-level voltage high-speed data signaling HIGH-level voltage Chirp J level (differential voltage) Chirp K level (differential voltage) off-state leakage current input capacitance pull-down resistance on pin DP pull-down resistance on pin DM driver output impedance on pin DP steady-state drive driver output impedance on pin DM input impedance exclusive of pull-up/pull-down (for low-/full-speed) steady-state drive
[1] [1]
Parameter termination voltage for upstream facing port pull-up
Conditions for 1.5 k pull-up resistor
Min 3.0
Typ -
Max 3.6
Unit V
100
-
150
mV
VHSDSC
525
-
625
mV
VHSDI VHSCM
|VDP - VDM| includes VDI range
300 -50
-
+500
mV mV
VHSOI VHSOL
-10 -10
-
+10 +10
mV mV
Output levels VHSOH VCHIRPJ VCHIRPK ILZ Cin Resistance RDN(DP) RDN(DM) ZO(drv)(DP) ZO(drv)(DM) ZINP 14.25 14.25 40.5 40.5 10 15 15 45 45 15.75 15.75 49.5 49.5 k k M 360 700 -900 -1 pin to GND 440 1100 -500 +1 5 mV mV mV A pF
Leakage current Capacitance
Termination
[1]
For high-speed USB and full-speed USB.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
57 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 49. Static characteristics: charge pump VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Typical values are at VCC = 3.3 V; VCC(I/O) = 1.8 V; Tamb = +25 C; unless otherwise specified. Symbol Voltage VO(VBUS) VL(VBUS) Current IO(VBUS) Efficiency cp charge pump efficiency IO(VBUS) = 50 mA 60 72 78 % output current on pin VBUS Ccp(C_A)-(C_B) = 270 nF 45 75 mA output voltage on pin VBUS leakage voltage on pin VBUS IO(VBUS) = 50 mA; Ccp(C_A)-(C_B) = 270 nF charge pump disabled 4.65 5.0 5.25 0.2 V V Parameter Conditions Min Typ Max Unit
Table 50. Static characteristics: VBUS comparators VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Typical values are at VCC = 3.3 V; VCC(I/O) = 1.8 V; Tamb = +25 C; unless otherwise specified. Symbol VA_VBUS_VLD VA_SESS_VLD Parameter A-device VBUS valid voltage A-device session valid voltage for A-device and B-device Conditions Min 4.4 0.8 70 0.2 Typ 4.5 1.6 90 0.5 Max 4.65 2.0 120 0.8 Unit V V mV V
Vhys(A_SESS_VLD) A-device session valid hysteresis voltage VB_SESS_END B-device session end voltage
Table 51. Static characteristics: VBUS resistors VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Typical values are at VCC = 3.3 V; VCC(I/O) = 1.8 V; Tamb = +25 C; unless otherwise specified. Symbol RUP(VBUS) RDN(VBUS) RI(idle)(VBUS)(A) RI(idle)(VBUS)(B) Parameter pull-up resistance on pin VBUS pull-down resistance on pin VBUS idle input resistance on pin VBUS (A-device) idle input resistance on pin VBUS (B-device) Conditions connect to REG3V3 when CHRG_VBUS is logic 1 connect to GND when DISCHRG_VBUS is logic 1 ID pin LOW and charge pump disabled ID pin HIGH or charge pump enabled Min 281 656 40 170 Typ 680 1100 54 230 Max 80 310 Unit k k
Table 52. Static characteristics: ID detection circuit VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Typical values are at VCC = 3.3 V; VCC(I/O) = 1.8 V; Tamb = +25 C; unless otherwise specified. Symbol tID Vth(ID) RUP(ID) Parameter ID detection time ID detector threshold voltage ID pull-up resistance ID_PULLUP is logic 1 Conditions Min 50 0.8 40 Typ 1.2 50 Max 2.0 60 Unit ms V k
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
58 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 53. Static characteristics: resistor reference VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Typical values are at VCC = 3.3 V; VCC(I/O) = 1.8 V; Tamb = +25 C; unless otherwise specified. Symbol VO(RREF) Parameter output voltage on pin RREF Conditions SUSPENDM is logic 1 Min Typ 1.22 Max Unit V
120 ICC(cp) (mA) 100 VCC = 3.6 V 80 3.3 V 3.0 V
004aaa876
5.50 VCC = 3.6 V VO(VBUS) (V) 5.00 3.3 V 3.0 V
004aaa877
60
40
4.50
20
0 0 10 20 30 40 IO(VBUS) (mA) 50
4.00 0 10 20 30 40 50 IO(VBUS) (mA)
ICC(cp) denotes the charge pump supply current.
Fig 22. Charge pump supply current as a function of VBUS output current
004aaa878
Fig 23. VBUS output voltage as a function of VBUS output current
004aaa879
5.50 VO(VBUS) (V) 5.00
108 ICC(cp) (mA) 106
IO(VBUS) = 0 mA 8 mA 50 mA
IO(VBUS) = 50 mA 104
4.50 102
4.00 3 3.1 3.2 3.3 3.4 3.6 VCC(cp) (V) 3.5
100 -40
-20
0
+20
+40
+60
+80 +100 Tamb (C)
VCC(cp) denotes the charge pump supply voltage.
ICC(cp) denotes the charge pump supply current.
Fig 24. VBUS output voltage as a function of charge pump supply voltage
Fig 25. Charge pump supply current as a function of temperature
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
59 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
15. Dynamic characteristics
Table 54. Dynamic characteristics: reset and clock VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Typical values are at VCC = 3.3 V; VCC(I/O) = 1.8 V; Tamb = +25 C; unless otherwise specified. Symbol Reset tW(POR) tw(REG1V8_H) tw(REG1V8_L) tW(RESET_N) tPWRUP internal power-on reset pulse width REG1V8 HIGH pulse width REG1V8 LOW pulse width external RESET_N pulse width regulator start-up time 4.7 F 20 % capacitor each on pins REG1V8 and REG3V3 ISP1506ABS ISP1506BBS tjit(i)(XTAL1)RMS i(XTAL1) RMS input jitter on pin XTAL1 input duty cycle on pin XTAL1 ISP1506ABS ISP1506BBS applicable only when clock is applied on pin XTAL1
[1]
Parameter
Conditions
Min 0.2 2 11 200 -
Typ -
Max 1
Unit s s s ns ms
Crystal or clock applied to XTAL1 fi(XTAL1) input frequency on pin XTAL1 19.2 26 50 200 300 MHz MHz ps ps %
fi(XTAL1) tr(XTAL1) tf(XTAL1) V(XTAL1)(p-p)
input frequency tolerance on pin XTAL1 rise time on pin XTAL1 fall time on pin XTAL1 peak-to-peak voltage on pin XTAL1 output frequency on pin CLOCK RMS output jitter on pin CLOCK output clock duty cycle on pin CLOCK PLL start-up time output CLOCK start-up time measured from power good or assertion of pin STP only for square wave input only for square wave input only for square wave input
0.566
50 -
200 5 5 1.95
ppm ns ns V
Output CLOCK characteristics fo(CLOCK) tjit(o)(CLOCK)RMS o(CLOCK) tstartup(PLL) tstartup(o)(CLOCK) 45 450 60 50 650 650 500 55 900 MHz ps % s s
[1]
The internal PLL is triggered only on the positive edge from the crystal oscillator. Therefore, the duty cycle is not critical.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
60 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 55. Dynamic characteristics: digital I/O pins VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Symbol tsu(DATA) th(DATA) td(DATA) tsu(STP) th(STP) td(DIR) td(NXT) Parameter Conditions Min 3.0 0 4.7 0 Typ Max 5.0 8.7 8.7 Unit ns ns ns ns ns ns ns DATA set-up time with respect to 20 pF total external load the rising edge of pin CLOCK per pin DATA hold time with respect to the rising edge of pin CLOCK 20 pF total external load per pin
DATA output delay with respect 20 pF total external load to the rising edge of pin CLOCK per pin STP set-up time with respect to the rising edge of pin CLOCK STP hold time with respect to the rising edge of pin CLOCK 20 pF total external load per pin 20 pF total external load per pin
DIR output delay with respect to 20 pF total external load the rising edge of pin CLOCK per pin NXT output delay with respect to 20 pF total external load the rising edge of pin CLOCK per pin
Table 56. Dynamic characteristics: analog I/O pins (DP and DM) VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Symbol tHSR tHSF tFR tFF tFRFM VCRS Parameter rise time (10 % to 90 %) fall time (10 % to 90 %) rise time fall time differential rise and fall time matching output signal crossover voltage transition time: rise time CL = 50 pF; 10 % to 90 % of |VOH - VOL| CL = 50 pF; 10 % to 90 % of |VOH - VOL| excluding the first transition from the idle state excluding the first transition from the idle state CL = 200 pF to 600 pF; 1.5 k pull-up on pin DM enabled; 10 % to 90 % of |VOH - VOL| CL = 200 pF to 600 pF; 1.5 k pull-up on pin DM enabled; 10 % to 90 % of |VOH - VOL| Conditions Min 500 500 4 4 90 1.3 Typ Max 20 20 111.1 2.0 Unit ps ps ns ns % V High-speed driver
Full-speed driver
Low-speed driver tLR 75 300 ns
tLF
transition time: fall time
75
-
300
ns
tLRFM
rise and fall time matching tLR/tLF; excluding the first transition from the idle state driver propagation delay (LOW to HIGH) driver propagation delay (HIGH to LOW) DAT, SE0 to DP, DM; see Figure 27 DAT, SE0 to DP, DM; see Figure 27
80
-
125
%
Driver timing tPLH(drv) tPHL(drv) 11 11 ns ns
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
61 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Table 56. Dynamic characteristics: analog I/O pins (DP and DM) ...continued VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 1.95 V; Tamb = -40 C to +85 C; unless otherwise specified. Symbol tPHZ tPLZ tPZH tPZL Parameter driver disable delay from HIGH level driver disable delay from LOW level driver enable delay to HIGH level driver enable delay to LOW level Conditions TX_ENABLE to DP, DM; see Figure 28 TX_ENABLE to DP, DM; see Figure 28 TX_ENABLE to DP, DM; see Figure 28 TX_ENABLE to DP, DM; see Figure 28 Min Typ Max 12 12 20 20 Unit ns ns ns ns
Receiver timing Differential receiver tPLH(rcv) tPHL(rcv) receiver propagation delay (LOW to HIGH) receiver propagation delay (HIGH to LOW) DP, DM to DAT, SE0; see Figure 29 DP, DM to DAT, SE0; see Figure 29 17 17 ns ns
1.8 V logic input 0.9 V tHSR, tFR, tLR VOH tHSF, tFF, tLF 0V 90 % 90 % tPLH(drv) VOH 10 %
004aaa861
0.9 V
tPHL(drv)
VOL
10 %
differential data lines VOL
VCRS
VCRS
004aaa573
Fig 26. Rise time and fall time
Fig 27. Timing of DAT and SE0 when transmitting to DP and DM
2.0 V 0.9 V differential data lines 0.8 V VCRS VCRS
1.8 V logic 0.9 V input 0V VOH differential data lines VOL tPZH tPZL VCRS VOL + 0.3 V
004aaa574
tPHZ tPLZ VOH - 0.3 V
tPLH(rcv) VOH logic output VOL 0.9 V
tPHL(rcv)
0.9 V
004aaa985
Fig 28. Timing of TX_ENABLE to DP and DM
Fig 29. Timing of DAT and SE0 when receiving from DP and DM
15.1 ULPI timing
ULPI interface timing requirements are given in Figure 30. This timing applies to synchronous mode only. All timing is measured with respect to the ISP1506 CLOCK pin. All signals are clocked on the rising edge of CLOCK.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
62 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
CLOCK tsu(STP) th(STP) CONTROL IN (STP) tsu(DATA) th(DATA)
DATA IN (8-BIT) td(DIR), td(NXT) CONTROL OUT (DIR, NXT) td(DATA) DATA OUT (8-BIT)
004aaa722
td(DIR), td(NXT)
Fig 30. ULPI timing interface
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
63 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
16. Application information
Table 57. Cbypass Ccp(C_A)-(C_B) Cfilter Recommended bill of materials Value 0.1 F 22 nF (8 mA), 270 nF (50 mA); up to 470 nF (50 mA) Comment highly recommended for all applications charge pump is used highly recommended for all applications mandatory for peripherals mandatory for host mandatory for OTG DESD Designator[1] Application
4.7 F 20 %; use a LOW ESR capacitor (0.2 to 2 ) for best performance 0.1 F and 1 F to 10 F in parallel -
CVBUS
0.1 F and 120 F 20 % (min) in parallel 0.1 F and 1 F to 6.5 F in parallel Wafer-Level Chip-Scale Package (WLCSP); ESD IEC 61000-4-2 level 4; 15 kV contact; 15 kV air discharge compliant protection maximum value is determined by the voltage drop on PSW_N caused by leakage into PSW_N and the external supply control pin -
recommended for all IP4359CX4/LF ESD-sensitive applications recommended; for applications with an external VBUS supply controlled by PSW_N mandatory in all applications 4.7 k (recommended)
Rpullup
RRREF RVBUS
12 k 1 %
strongly recommended for 1 k 5 % peripheral or external 5 V applications only required only for applications driving a square wave into the XTAL1 pin crystal is used required only for applications driving a square wave into the XTAL1 pin that has a DC offset 47 k 5 %
RXTAL
used to avoid floating input on the XTAL1 pin
XTAL C(XTAL)SQ
19.2 MHz 26 MHz 100 pF
CL = 10 pF; RS < 220 ; CXTAL = 18 pF CL = 10 pF; RS < 130 ; CXTAL = 18 pF used to AC couple the input square wave to the XTAL1 pin
[1]
For detailed information, refer to application note Ref. 7 "Interfacing to the ISP1504/5/6 (AN10048)".
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
64 of 79
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Product data sheet Rev. 02 -- 28 August 2008
(c) NXP B.V. 2008. All rights reserved. ISP1506A_ISP1506B_2
NXP Semiconductors
VCC(I/O) VCC
Cbypass Cbypass
Cbypass
VCC(I/O)
RRREF
1
24
DATA0
1 2 3 4 USB MICRO-AB RECEPTACLE 5
VBUS D- D+ ID GND A1 SHIELD A2 B2
DESD
RREF
2
23
DATA1 DATA0 DATA2 DATA1 VCC(I/O) DATA2 DATA3 DATA3 CLOCK CLOCK NXT NXT STP DIR OTG CONTROLLER
DM
3
22
DP
4
21
ID 5 CPGND 6
20
19
IP4359CX4/LF
B1 C_B 7
Ccp(C_A)-(C_B)
6 SHIELD 7 SHIELD 8 SHIELD 9
ISP1506
18
C_A 8 VCC
17
STP
9
16
DIR
ISP1506A; ISP1506B
VBUS/FAULT
CVBUS
10
15
REG1V8
REG3V3 11 XTAL1 12 GND (die pad)
Cfilter Cbypass XTAL(1)
14
RESET_N/PSW_N
ULPI HS USB OTG transceiver
13
XTAL2
Cbypass Cfilter
CXTAL
CXTAL
004aaa602
65 of 79
(1) Frequency is version dependent: ISP1506A: 19.2 MHz; ISP1506B: 26 MHz.
Fig 31. Using the ISP1506 with an OTG controller; internal charge pump is utilized and crystal is attached
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Product data sheet Rev. 02 -- 28 August 2008
(c) NXP B.V. 2008. All rights reserved. ISP1506A_ISP1506B_2
NXP Semiconductors
VCC
VCC(I/O)
Rpullup
+3.3 V
IN CHARGE PUMP
+5 V OUT
Cbypass
Cbypass
ON
VCC(I/O) 1 VBUS D- D+ ID GND CPGND SHIELD SHIELD SHIELD A1 A2 C_B 7
Cbypass DESD RRREF RREF
24
DATA0
DATA0
1 2 3 4 USB MICRO-AB RECEPTACLE 5 6 7 8
2 DM 3 DP 4 ID 5
23
DATA1
DATA1
22
DATA2
DATA2
21
VCC(I/O)
DATA3 OTG CONTROLLER CLOCK
20
DATA3
6
19
CLOCK
NXT
ISP1506
18 NXT STP STP DIR DIR
IP4359CX4/LF
B1 B2
C_A 8 VCC
RVBUS VBUS/FAULT CVBUS
17
9 SHIELD
9
16
ISP1506A; ISP1506B
10
15
REG1V8
REG3V3 11 XTAL1 14
RESET_N/PSW_N
ULPI HS USB OTG transceiver
Cbypass
Cfilter
12
GND (die pad)
13
XTAL2
Cbypass
Cfilter
fi(XTAL1)(1)
C(XTAL)SQ
RXTAL
004aaa887
(1) Frequency is version dependent: ISP1506A: 19.2 MHz; ISP1506B: 26 MHz.
66 of 79
Fig 32. Using the ISP1506 with an OTG controller; external charge pump using ISP1506 internal VBUS valid and external square wave input on XTAL1
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Product data sheet Rev. 02 -- 28 August 2008
(c) NXP B.V. 2008. All rights reserved. ISP1506A_ISP1506B_2
NXP Semiconductors
VCC
VCC(I/O)
Rpullup
+5 V IN ON VBUS SWITCH
Cbypass
Cbypass
Cbypass
FAULT OUT VCC(I/O) 24 DATA0 DATA0
1
1
VBUS
RRREF RREF
2
23
DATA1
DATA1
2
D-
DM
3
22
DATA2
DATA2
USB 3 STANDARD-A RECEPTACLE 4
D+
DP
4
21
VCC(I/O)
DATA3 HOST CONTROLLER CLOCK
GND
A1
A3
ID
5
IP4359CX4/LF
5 SHIELD B1 B2
DESD
20
DATA3
CPGND
6
19
CLOCK NXT NXT STP STP DIR DIR
6
SHIELD
CVBUS
C_B
ISP1506
7 18
C_A
8 17
VCC
9 16
ISP1506A; ISP1506B
VBUS/FAULT
10 15
REG1V8
REG3V3
11 14
RESET_N/PSW_N
Cbypass Cfilter
ULPI HS USB OTG transceiver
XTAL1
Cbypass Cfilter
12 13 GND (die pad)
XTAL2
fi(XTAL1)(1)
C(XTAL)SQ
RXTAL
004aaa888
67 of 79
(1) Frequency is version dependent: ISP1506A: 19.2 MHz; ISP1506B: 26 MHz.
Fig 33. Using the ISP1506 with a standard USB host controller; external 5 V source with built-in FAULT and external square wave input on XTAL1
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Product data sheet Rev. 02 -- 28 August 2008
(c) NXP B.V. 2008. All rights reserved. ISP1506A_ISP1506B_2
NXP Semiconductors
VCC
VCC(I/O)
Cbypass Cbypass
Cbypass
VCC(I/O) 1
RRREF
24
DATA0
DATA0
1 2 3 USB STANDARD-B RECEPTACLE 4 5 6
VBUS D-
RREF 2 DM 3 DP
23
DATA1
DATA1
22
DATA2 DATA2 VCC(I/O) DATA3 PERIPHERAL CONTROLLER CLOCK
D+
4
21
GND A1 SHIELD A2
ID
5
20
DATA3
IP4359CX4/LF
B1
DESD
CPGND
RVBUS
6
19
CLOCK NXT
SHIELD
B2 C_B 7
ISP1506
18
NXT STP
C_A
8 17
STP DIR
VCC
9 16
DIR
ISP1506A; ISP1506B
VBUS/FAULT 10
CVBUS
15 REG3V3 11 14 XTAL1 12
REG1V8 RESET_N/ PSW_N
Cbypass Cfilter
ULPI HS USB OTG transceiver
Cbypass
Cfilter XTAL(1)
XTAL2 13 GND (die pad)
CXTAL
CXTAL
004aaa889
68 of 79
(1) Frequency is version dependent: ISP1506A: 19.2 MHz; ISP1506B: 26 MHz.
Fig 34. Using the ISP1506 with a standard USB peripheral controller; external crystal is used
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
17. Package outline
HVQFN24: plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 4 x 4 x 0.85 mm
SOT616-1
D
B
A
terminal 1 index area A A1 E c
detail X
e1
1/2 e
C b 12 vMCAB wMC 13 e y1 C y
e 7 L 6
Eh
1/2 e
e2
1
18
terminal 1 index area
24 Dh 0
19 X 2.5 scale 5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A(1) max. 1 A1 0.05 0.00 b 0.30 0.18 c 0.2 D (1) 4.1 3.9 Dh 2.25 1.95 E (1) 4.1 3.9 Eh 2.25 1.95 e 0.5 e1 2.5 e2 2.5 L 0.5 0.3 v 0.1 w 0.05 y 0.05 y1 0.1
Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. OUTLINE VERSION SOT616-1 REFERENCES IEC --JEDEC MO-220 JEITA --EUROPEAN PROJECTION ISSUE DATE 01-08-08 02-10-22
Fig 35. Package outline SOT616-1 (HVQFN24)
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
69 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
18. Soldering of SMD packages
This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 "Surface mount reflow soldering description".
18.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization.
18.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following:
* Through-hole components * Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are:
* * * * * *
Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering
18.3 Wave soldering
Key characteristics in wave soldering are:
* Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are exposed to the wave
* Solder bath specifications, including temperature and impurities
ISP1506A_ISP1506B_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
70 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
18.4 Reflow soldering
Key characteristics in reflow soldering are:
* Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 36) than a SnPb process, thus reducing the process window
* Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
* Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 58 and 59
Table 58. SnPb eutectic process (from J-STD-020C) Package reflow temperature (C) Volume (mm3) < 350 < 2.5 2.5 Table 59. 235 220 Lead-free process (from J-STD-020C) Package reflow temperature (C) Volume (mm3) < 350 < 1.6 1.6 to 2.5 > 2.5 260 260 250 350 to 2000 260 250 245 > 2000 260 245 245 350 220 220
Package thickness (mm)
Package thickness (mm)
Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 36.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
71 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
temperature
maximum peak temperature = MSL limit, damage level
minimum peak temperature = minimum soldering temperature
peak temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 36. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365 "Surface mount reflow soldering description".
19. Abbreviations
Table 60. Acronym ASIC ATX CD-RW EOP ESD ESR FS HBM HNP HS ID IEC LS NRZI OTG PCB PHY PID PLL
ISP1506A_ISP1506B_2
Abbreviations Description Application-Specific Integrated Circuit Analog USB Transceiver Compact Disc-ReWritable End-Of-Packet ElectroStatic Discharge Effective Series Resistance Full-Speed Human Body Model Host Negotiation Protocol High-Speed Identification International Electrotechnical Commission Low-Speed Non-Return-to-Zero Inverted On-The-Go Printed-Circuit Board Physical Layer Packet Identifier Phase-Locked Loop
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
72 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
Abbreviations ...continued Description Power-On Reset Receive Command Single-Ended Zero Start-Of-Frame Session Request Protocol Synchronous Transistor-Transistor Logic Transmit Command Universal Serial Bus USB Implementers Forum UTMI+ Low Pin Interface USB 2.0 Transceiver Macrocell Interface USB 2.0 Transceiver Macrocell Interface Plus
Table 60. Acronym POR RXCMD SE0 SOF SRP SYNC TTL TXCMD USB USB-IF ULPI UTMI UTMI+
20. References
[1] [2] [3] [4] [5] [6] [7] Universal Serial Bus Specification Rev. 2.0 On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3 UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1 UTMI+ Specification Rev. 1.0 USB 2.0 Transceiver Macrocell Interface (UTMI) Specification Ver. 1.05 Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM) (JESD22-A114D) Interfacing to the ISP1504/5/6 (AN10048)
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
73 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
21. Revision history
Table 61. Revision history Release date 20080828 Data sheet status Product data sheet Change notice Supersedes ISP1506A_ISP1506B_1 Document ID ISP1506A_ISP1506B_2 Modifications:
* * * * * * * * * *
Globally changed mini-USB, mini-A and mini-B connectors to micro-USB, micro-A and micro-B connectors, respectively. Section 8.2 "USB and OTG state transitions": updated the first sentence. Figure 6 "Power-up and reset sequence required before the ULPI bus is ready for use": updated. Section 9.4.2 "Fault detection": updated. Section "Standard USB host controllers": updated the first list item. Section "OTG devices": updated the last sentence. Section 9.10.1 "Full-speed or low-speed host-initiated suspend and resume": updated list item 2. Section 9.10.2 "High-speed suspend and resume": updated list item 2. Table 42 "Power Control register (address R = 3Dh to 3Fh, W = 3Dh, S = 3Eh, C = 3Fh) bit description": updated description of bits 3 and 2. Table 43 "Limiting values" and Table 44 "Recommended operating conditions": removed CLOCK from the conditions column. Product data sheet -
ISP1506A_ISP1506B_1
20070530
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
74 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
22. Legal information
22.1 Data sheet status
Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet
[1] [2] [3]
Product status[3] Development Qualification Production
Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification.
Please consult the most recently issued document before initiating or completing a design. The term `short data sheet' is explained in section "Definitions". The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
22.2 Definitions
Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.
malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.
22.3 Disclaimers
General -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or
22.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners.
23. Contact information
For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
75 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
24. Tables
Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Ordering information . . . . . . . . . . . . . . . . . . . . .3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .5 Recommended charge pump capacitor value .12 ULPI signal description . . . . . . . . . . . . . . . . . .15 Signal mapping during low-power mode . . . . .16 Signal mapping for 3-pin serial mode . . . . . . .17 Operating states and their corresponding resistor settings . . . . . . . . . . . . . . . . . . . . . . . .18 OTG Control register power control bits . . . . .24 TXCMD byte format . . . . . . . . . . . . . . . . . . . . .24 RXCMD byte format . . . . . . . . . . . . . . . . . . . . .25 LINESTATE[1:0] encoding for upstream facing ports: peripheral . . . . . . . . . . . . . . . . . .26 LINESTATE[1:0] encoding for downstream facing ports: host . . . . . . . . . . . . . . . . . . . . . . .26 Encoded VBUS voltage state . . . . . . . . . . . . . .26 VBUS indicators in RXCMD required for typical applications . . . . . . . . . . . . . . . . . . . . . .27 Encoded USB event signals . . . . . . . . . . . . . .28 PHY pipeline delays . . . . . . . . . . . . . . . . . . . . .32 Link decision times . . . . . . . . . . . . . . . . . . . . .33 Immediate register set overview . . . . . . . . . . .44 Extended register set overview . . . . . . . . . . . .44 Vendor ID Low register (address R = 00h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .45 Vendor ID High register (address R = 01h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .45 Product ID Low register (address R = 02h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .45 Product ID High register (address R = 03h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .45 Function Control register (address R = 04h to 06h, W = 04h, S = 05h, C = 06h) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Function Control register (address R = 04h to 06h, W = 04h, S = 05h, C = 06h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Interface Control register (address R = 07h to 09h, W = 07h, S = 08h, C = 09h) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Interface Control register (address R = 07h to 09h, W = 07h, S = 08h, C = 09h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 OTG Control register (address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh, C = 0Ch) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 OTG Control register (address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh, C = 0Ch) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 USB Interrupt Enable Rising Edge register (address R = 0Dh to 0Fh, W = 0Dh, S = 0Eh, C = 0Fh) bit allocation . . . . . . . . . . . .48 USB Interrupt Enable Rising Edge register (address R = 0Dh to 0Fh, W = 0Dh, S = 0Eh, C = 0Fh) bit description . . . . . . . . . .49 USB Interrupt Enable Falling Edge register (address R = 10h to 12h, W = 10h, S = 11h, C = 12h) bit allocation . . . . . . . . . . . . 49 USB Interrupt Enable Falling Edge register (address R = 10h to 12h, W = 10h, S = 11h, C = 12h) bit description . . . 49 USB Interrupt Status register (address R = 13h) bit allocation . . . . . . . . . . . 50 USB Interrupt Status register (address R = 13h) bit description . . . . . . . . . . 50 USB Interrupt Latch register (address R = 14h) bit allocation . . . . . . . . . . . 50 USB Interrupt Latch register (address R = 14h) bit description . . . . . . . . . . 50 Debug register (address R = 15h) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Debug register (address R = 15h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Scratch register (address R = 16h to 18h, W = 16h, S = 17h, C = 18h) bit description . . . 51 Power Control register (address R = 3Dh to 3Fh, W = 3Dh, S = 3Eh, C = 3Fh) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Power Control register (address R = 3Dh to 3Fh, W = 3Dh, S = 3Eh, C = 3Fh) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . . 54 Recommended operating conditions . . . . . . . . 54 Static characteristics: supply pins . . . . . . . . . . 55 Static characteristics: digital pins (CLOCK, DIR, STP, NXT, DATA[3:0], RESET_N/PSW_N) . . . . . . . . . . . . . . . . . . . . . 55 Static characteristics: digital pin FAULT . . . . . 56 Static characteristics: analog I/O pins (DP, DM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Static characteristics: charge pump . . . . . . . . 58 Static characteristics: VBUS comparators . . . . 58 Static characteristics: VBUS resistors . . . . . . . . 58 Static characteristics: ID detection circuit . . . . 58 Static characteristics: resistor reference . . . . . 59 Dynamic characteristics: reset and clock . . . . 60 Dynamic characteristics: digital I/O pins . . . . . 61 Dynamic characteristics: analog I/O pins (DP and DM) . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Recommended bill of materials . . . . . . . . . . . . 64 SnPb eutectic process (from J-STD-020C) . . . 71 Lead-free process (from J-STD-020C) . . . . . . 71 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 74
Table 33.
Table 34. Table 35. Table 36. Table 37. Table 38. Table 39. Table 40. Table 41.
Table 42.
Table 43. Table 44. Table 45. Table 46.
Table 47. Table 48. Table 49. Table 50. Table 51. Table 52. Table 53. Table 54. Table 55. Table 56. Table 57. Table 58. Table 59. Table 60. Table 61.
Table 25.
Table 26.
Table 27.
Table 28.
Table 29.
Table 30.
Table 31.
Table 32.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
76 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
25. Figures
Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. Fig 6. Fig 7. Fig 8. Fig 9. Fig 10. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Pin configuration HVQFN24; top view . . . . . . . . . .5 External capacitors connection . . . . . . . . . . . . . .10 Charge pump capacitor . . . . . . . . . . . . . . . . . . . .11 Internal power-on reset timing . . . . . . . . . . . . . . .20 Power-up and reset sequence required before the ULPI bus is ready for use. . . . . . . . . . . . . . . .22 Interface behavior with respect to RESET_N. . . .23 Single and back-to-back RXCMDs from the ISP1506 to the link. . . . . . . . . . . . . . . . . . . . . . . .25 RXCMD A_VBUS_VLD indicator source . . . . . . .27 Example of register write, register read, extended register write and extended register read. . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 USB reset and high-speed detection handshake (chirp) sequence . . . . . . . . . . . . . . . . . . . . . . . . .31 Example of using the ISP1506 to transmit and receive USB data . . . . . . . . . . . . . . . . . . . . . . . . .32 High-speed transmit-to-transmit packet timing. . .33 High-speed receive-to-transmit packet timing . . .34 Preamble sequence . . . . . . . . . . . . . . . . . . . . . . .35 Full-speed suspend and resume . . . . . . . . . . . . .36 High-speed suspend and resume . . . . . . . . . . . .38 Remote wake-up from low-power mode . . . . . . .40 Transmitting USB packets without the automatic SYNC and EOP generation . . . . . . . . . . . . . . . . .41 Example of transmit followed by receive in 3-pin serial mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Human body ESD test model. . . . . . . . . . . . . . . .53 Charge pump supply current as a function of VBUS output current . . . . . . . . . . . . . . . . . . . . .59 VBUS output voltage as a function of VBUS output current. . . . . . . . . . . . . . . . . . . . . . . . . . . .59 VBUS output voltage as a function of charge pump supply voltage . . . . . . . . . . . . . . . . . . . . . .59 Charge pump supply current as a function of temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 Rise time and fall time . . . . . . . . . . . . . . . . . . . . .62 Timing of DAT and SE0 when transmitting to DP and DM . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Timing of TX_ENABLE to DP and DM. . . . . . . . .62 Timing of DAT and SE0 when receiving from DP and DM . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 ULPI timing interface . . . . . . . . . . . . . . . . . . . . . .63 Using the ISP1506 with an OTG controller; internal charge pump is utilized and crystal is attached . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Using the ISP1506 with an OTG controller; external charge pump using ISP1506 internal VBUS valid and external square wave input on XTAL1 . . . . . . . . . . . . . . . . . . . . . .66 Using the ISP1506 with a standard USB host controller; external 5 V source with built-in FAULT and external square wave input on XTAL1. . . . . .67 Using the ISP1506 with a standard USB peripheral controller; external crystal is used . . .68 Fig 35. Package outline SOT616-1 (HVQFN24) . . . . . . . 69 Fig 36. Temperature profiles for large and small components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Fig 11. Fig 12. Fig 13. Fig 14. Fig 15. Fig 16. Fig 17. Fig 18. Fig 19. Fig 20. Fig 21. Fig 22. Fig 23. Fig 24. Fig 25. Fig 26. Fig 27. Fig 28. Fig 29. Fig 30. Fig 31.
Fig 32.
Fig 33.
Fig 34.
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
77 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
26. Contents
1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 Ordering information . . . . . . . . . . . . . . . . . . . . . 3 5 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4 6 Pinning information . . . . . . . . . . . . . . . . . . . . . . 5 6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 7 Functional description . . . . . . . . . . . . . . . . . . . 7 7.1 ULPI interface controller . . . . . . . . . . . . . . . . . . 7 7.2 USB data serializer and deserializer. . . . . . . . . 7 7.3 Hi-Speed USB (USB 2.0) ATX . . . . . . . . . . . . . 7 7.4 Voltage regulator. . . . . . . . . . . . . . . . . . . . . . . . 8 7.5 Crystal oscillator and PLL. . . . . . . . . . . . . . . . . 8 7.6 OTG module . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 7.6.1 ID detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 7.6.2 VBUS comparators. . . . . . . . . . . . . . . . . . . . . . . 9 7.6.2.1 VBUS valid comparator . . . . . . . . . . . . . . . . . . . 9 7.6.2.2 Session valid comparator . . . . . . . . . . . . . . . . . 9 7.6.2.3 Session end comparator. . . . . . . . . . . . . . . . . . 9 7.6.3 SRP charge and discharge resistors . . . . . . . . 9 7.6.4 Charge pump . . . . . . . . . . . . . . . . . . . . . . . . . . 9 7.7 Band gap reference voltage . . . . . . . . . . . . . . 10 7.8 Power-On Reset (POR) . . . . . . . . . . . . . . . . . 10 7.9 Detailed description of pins . . . . . . . . . . . . . . 10 7.9.1 DATA[3:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.9.2 VCC(I/O) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.9.3 RREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.9.4 DP and DM . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.9.5 ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.9.6 CPGND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.9.7 C_A and C_B . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.9.8 VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7.9.9 VBUS/FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7.9.9.1 VBUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7.9.9.2 FAULT (external overcurrent or fault detector) 12 7.9.10 REG3V3 and REG1V8 . . . . . . . . . . . . . . . . . . 12 7.9.11 XTAL1 and XTAL2. . . . . . . . . . . . . . . . . . . . . . 12 7.9.12 RESET_N/PSW_N . . . . . . . . . . . . . . . . . . . . . 13 7.9.12.1 RESET_N . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7.9.12.2 PSW_N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7.9.13 DIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7.9.14 STP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7.9.15 NXT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7.9.16 CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7.9.17 GND (die pad). . . . . . . . . . . . . . . . . . . . . . . . . 14 8 Modes of operation . . . . . . . . . . . . . . . . . . . . . 15 8.1 ULPI modes . . . . . . . . . . . . . . . . . . . . . . . . . . 15 8.1.1 Synchronous mode . . . . . . . . . . . . . . . . . . . . 15 8.1.2 Low-power mode . . . . . . . . . . . . . . . . . . . . . . 16 8.1.3 3-pin full-speed or low-speed serial mode . . . 17 8.2 USB and OTG state transitions . . . . . . . . . . . 17 9 Protocol description . . . . . . . . . . . . . . . . . . . . 20 9.1 ULPI references . . . . . . . . . . . . . . . . . . . . . . . 20 9.2 Power-On Reset (POR) . . . . . . . . . . . . . . . . . 20 9.3 Power-up, reset and bus idle sequence . . . . . 20 9.3.1 Interface protection. . . . . . . . . . . . . . . . . . . . . 22 9.3.2 Interface behavior with respect to RESET_N. 23 9.4 VBUS power and fault detection . . . . . . . . . . . 23 9.4.1 Driving 5 V on VBUS . . . . . . . . . . . . . . . . . . . . 23 9.4.2 Fault detection . . . . . . . . . . . . . . . . . . . . . . . . 24 9.5 TXCMD and RXCMD . . . . . . . . . . . . . . . . . . . 24 9.5.1 TXCMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 9.5.2 RXCMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 9.5.2.1 Linestate encoding . . . . . . . . . . . . . . . . . . . . . 25 9.5.2.2 VBUS state encoding . . . . . . . . . . . . . . . . . . . . 26 9.5.2.3 Using and selecting the VBUS state encoding. 27 9.5.2.4 RxEvent encoding . . . . . . . . . . . . . . . . . . . . . 28 9.6 Register read and write operations . . . . . . . . 29 9.7 USB reset and high-speed detection handshake (chirp) . . . . . . . . . . . . . . . . . . . . . 29 9.8 USB packet transmit and receive . . . . . . . . . . 32 9.8.1 USB packet timing . . . . . . . . . . . . . . . . . . . . . 32 9.8.1.1 ISP1506 pipeline delays. . . . . . . . . . . . . . . . . 32 9.8.1.2 Allowed link decision time . . . . . . . . . . . . . . . 32 9.9 Preamble . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 9.10 USB suspend and resume . . . . . . . . . . . . . . . 35 9.10.1 Full-speed or low-speed host-initiated suspend and resume . . . . . . . . . . . . . . . . . . . . . . . . . . 35 9.10.2 High-speed suspend and resume . . . . . . . . . 36 9.10.3 Remote wake-up . . . . . . . . . . . . . . . . . . . . . . 39 9.11 No automatic SYNC and EOP generation (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 9.12 On-The-Go operations . . . . . . . . . . . . . . . . . . 41 9.12.1 OTG charge pump . . . . . . . . . . . . . . . . . . . . . 42 9.12.2 OTG comparators. . . . . . . . . . . . . . . . . . . . . . 42 9.12.3 Pull-up and pull-down resistors . . . . . . . . . . . 42 9.12.4 ID detection . . . . . . . . . . . . . . . . . . . . . . . . . . 42 9.12.5 VBUS charge and discharge resistors . . . . . . . 42 9.13 Serial mode . . . . . . . . . . . . . . . . . . . . . . . . . . 42 9.14 Aborting transfers. . . . . . . . . . . . . . . . . . . . . . 43 9.15 Avoiding contention on the ULPI data bus . . . 43 10 Register map . . . . . . . . . . . . . . . . . . . . . . . . . . 44 10.1 Immediate register set . . . . . . . . . . . . . . . . . . 45
continued >>
ISP1506A_ISP1506B_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 28 August 2008
78 of 79
NXP Semiconductors
ISP1506A; ISP1506B
ULPI HS USB OTG transceiver
45 45 45 45 45 45 46 47 48 49 49 50 51 51 51 51 51 51 52 53 53 53 54 54 55 60 62 64 69 70 70 70 70 71 72 73 74 75 75 75 75 75 75 76 77 78
10.1.1 Vendor ID and Product ID registers . . . . . . . . 10.1.1.1 Vendor ID Low register . . . . . . . . . . . . . . . . . . 10.1.1.2 Vendor ID High register . . . . . . . . . . . . . . . . . 10.1.1.3 Product ID Low register . . . . . . . . . . . . . . . . . 10.1.1.4 Product ID High register . . . . . . . . . . . . . . . . . 10.1.2 Function Control register . . . . . . . . . . . . . . . . 10.1.3 Interface Control register . . . . . . . . . . . . . . . . 10.1.4 OTG Control register . . . . . . . . . . . . . . . . . . . 10.1.5 USB Interrupt Enable Rising Edge register . . 10.1.6 USB Interrupt Enable Falling Edge register . . 10.1.7 USB Interrupt Status register . . . . . . . . . . . . . 10.1.8 USB Interrupt Latch register . . . . . . . . . . . . . . 10.1.9 Debug register . . . . . . . . . . . . . . . . . . . . . . . . 10.1.10 Scratch register. . . . . . . . . . . . . . . . . . . . . . . . 10.1.11 Reserved . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1.12 Access extended register set . . . . . . . . . . . . . 10.1.13 Vendor-specific registers . . . . . . . . . . . . . . . . 10.1.14 Power Control register . . . . . . . . . . . . . . . . . . 10.2 Extended register set . . . . . . . . . . . . . . . . . . . 11 ElectroStatic Discharge (ESD) . . . . . . . . . . . . 11.1 ESD protection . . . . . . . . . . . . . . . . . . . . . . . . 11.2 ESD test conditions . . . . . . . . . . . . . . . . . . . . 12 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 13 Recommended operating conditions. . . . . . . 14 Static characteristics. . . . . . . . . . . . . . . . . . . . 15 Dynamic characteristics . . . . . . . . . . . . . . . . . 15.1 ULPI timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Application information. . . . . . . . . . . . . . . . . . 17 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 18 Soldering of SMD packages . . . . . . . . . . . . . . 18.1 Introduction to soldering . . . . . . . . . . . . . . . . . 18.2 Wave and reflow soldering . . . . . . . . . . . . . . . 18.3 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 18.4 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 19 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 20 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 22 Legal information. . . . . . . . . . . . . . . . . . . . . . . 22.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 22.2 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22.3 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 22.4 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Contact information. . . . . . . . . . . . . . . . . . . . . 24 Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'.
(c) NXP B.V. 2008.
All rights reserved.
For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 28 August 2008 Document identifier: ISP1506A_ISP1506B_2

▲Up To Search▲

Price & Availability of ISP1506A08

	To Download ISP1506A08 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .